Advanced Matrix Office Printer Plus True True DM/C P, S opt LQ False False
Advanced Matrix TracJet True True L S, P LJ II False False
Advanced Matrix TracJet II True True L S, P LJ II False False
Advanced Technologies AT-7030 True True L S, P LJ III False False
Advanced Technologies LaserPrint O880/DW-2 True False L S, P LJ False False
Advanced Technologies LaserPrint 0880/DW-3 True False L S, P LJ False False
Advanced Technologies LaserPrint 1270 True False L LJ False False
Advanced Technologies LaserPrint 1275 True False L LJ False False
Advanced Technologies LaserPrint 1570/DW-2 True False L S, P LJ False False
Advanced Technologies LaserPrint 1570/DW-3 True False L S, P LJ False False
Advanced Technologies LaserPrint 2670/DW-2 True False L S, P LJ False False
Advanced Technologies LaserPrint 2670/DW-3 True False L S, P LJ False False
Advanced Technologies LC-2615 True False L S, P LJ False False
Advanced Technologies LC-6020 True False L S, P LJ False False
Advanced Technologies LC-6026 True False L S, P LJ False False
Advanced Technologies LC-6050 True False L S, P LJ False False
Advanced Technologies LC-6815 True True L S, P LJ II False False
Advanced Technologies LC-6820 True False L S, P LJ False False
Advanced Technologies LC-6850 True False L S, P LJ False False
Advanced Technologies LC-9125 True True L P LJ II False False
Aedex Corp 608 True False L S or P LJ False False Parallel interface required.
AEG Olympia Laserstar 6 True False L S, P LJ False False
AEG Olympia Laserstar 6e True True L S, P LJ II False False
AEG Olympia NP 30 True True DM P, S opt FX False False
AEG Olympia NP 60 True True DM P, S opt FX False False
AEG Olympia NP 80 SE True True DM S, P FX False False
AEG Olympia NP 80-24 True True DM S, P LQ False False
AEG Olympia NP 80-24E True True DM P, S opt LQ False False
AEG Olympia NP 136 SE True True DM S, P FX False False
AEG Olympia NP 136-24 True True DM S, P LQ False False
AEG Olympia NPC 136-24 True True DM/C S, P LQ False False
AI/GBT 6824 XP True True L P opt LJ II False False Parallel interface required.
AI/GBT 6840 XP True True L P opt LJ II False False Parallel interface required.
AI/GBT 6845 XP True True L P opt LJ II False False Parallel interface required.
Alps Allegro 24 True True DM P, S opt LQ False False I This card provides you with detailed instructions for setting the Memory Mode for the printer’s parallel interface to work with PowerPrint. The following settings will be made: Line Spacing, Front Panel Font Selection, Extended Character Set, Form Length, Print Variation, 1 Inch Perforation Skip, Detect Paper Out, Automatic LF On Carriage Return, Top Of Form Setting, International Character Set, Audible Buzzer, Print Direction, Interface, ASF Installed, Select In Signal Fixed.®®Note: In this card we will be giving you step-by-step instructions for defining the Memory Mode. For more detailed information, refer to chapter 3 of the printer manual.®®Note: The LF and the SET TOF buttons are the same buttons. The FF and SET TOF buttons are the same buttons. The PITCH and the RESET buttons are the same buttons. The TEAR BAR and the PARK buttons are the same buttons.®®Note: When changing the Memory Mode settings, the LF button always selects the next setting down. The FF button always selects the next option across. Pressing the LF button to select the next setting automatically saves the last option.®®Note: If you lose track at any time while setting the Memory Mode, press the SELECT button, which returns the printer to normal operation in Select status, and start over.®®Follow these instructions to set the Memory Mode:®®1. To enter Memory Mode, first make sure the printer is properly loaded with paper and ribbon, and that the power is off. Then press and hold the SELECT button and turn the power on.®®The printer enters Memory Mode and immediately prints the entire Memory Mode menu, including the current setting of each item. It will then print the first item on the list again, along with its current setting, and feed the paper forward so that the last printed line is visible beyond the top cover.®®2. Press the LF button once. The printer will print the next setting, LINE SPACING along with the next option, 6 LPI. If the LINE SPACING is not set to 6 LPI, press the FF button until it does. Once the printer prints LINE SPACING 6 LPI, press the LF button three times.®®3. The printer will print the fifth setting, FRONT PANEL FONT SELECTION, along with the next option, FRONT PANEL SELECTION. If the FRONT PANEL FONT SELECTION is not set to FRONT PANEL SELECTION, press the FF button until it does. Once the printer prints FRONT PANEL FONT SELECTION FRONT PANEL SELECTION, press the LF button once.®®4. The printer will print the next setting, EXTENDED CHARACTER SET along with the next option, EPSON. If the EXTENDED CHARACTER SET is not set to EPSON, press the FF button until it does. Once the printer prints EXTENDED CHARACTER SET EPSON, press the LF button once.®®5. The printer will print the next setting, FORM LENGTH along with the next option, 11 INCHES. If the FORM LENGTH is not set to 11 INCHES, press the FF button until it does. Once the printer prints FORM LENGTH 11 INCHES, press the LF button once.®®6. The printer will print the next setting, PRINT VARIATION along with the next option, NORMAL. If the PRINT VARIATION is not set to NORMAL, press the FF button until it does. Once the printer prints PRINT VARIATION NORMAL, press the LF button once.®®7. The printer will print the next setting,1-INCH PERFORATION SKIP along with the first option NO. If the 1-INCH PERFORATION SKIP is not set to NO, press the FF button until it does. Once the printer prints 1-INCH PERFORATION SKIP NO, press the LF button once.®®8. The printer will print the next setting, DETECT PAPER OUT along with the first option, YES. If the DETECT PAPER OUT is not set to YES, press the FF button until it does. Once the printer prints DETECT PAPER OUT YES, press the LF button once.®®9. The printer will print the next setting, AUTOMATIC LF ON CARRIAGE RETURN along with the first option NO. If the AUTOMATIC LF ON CARRIAGE RETURN is not set to NO, press the FF button until it does. Once the printer prints AUTOMATIC LF ON CARRIAGE RETURN NO, press the LF button once.®®10. The printer will print the next setting TOP-OF-FORM SETTING, along with the first option, FIRST PRINT LINE. If the TOP-OF-FORM SETTING is not set to FIRST PRINT LINE, press the FF button until it does. Once the printer prints TOP-OF-FORM SETTING FIRST PRINT LINE, press the LF button once.®®11. The printer will print the next setting, INTERNATIONAL CHARACTER SET along with the first option, U.S.A. If the INTERNATIONAL CHARACTER SET is not set to U.S.A., press the FF button until it does. Once the printer prints INTERNATIONAL CHARACTER SET U.S.A., press the LF button twice.®®12. The printer will print the fifteenth setting, AUDIBLE BUZZER along with the first option, YES. If the AUDIBLE BUZZER is not set to YES, press the FF button until it does. Once the printer prints AUDIBLE BUZZER Yes, press the LF button once.®®13. The printer will print the next setting, PRINT DIRECTION FOR GRAPHICS along with the first option, BIDIRECTION. If the PRINT DIRECTION FOR GRAPHICS is not set to BIDIRECTION, press the FF button until it does. Once the printer prints PRINT DIRECTION FOR GRAPHICS BIDIRECTION, press the LF button once.®®14. The printer will print the next setting, INTERFACE along with the first option, PARALLEL. If the INTERFACE is not set to PARALLEL, press the FF button until it does. Once the printer prints INTERFACE PARALLEL, press the LF button once.®®15. The printer will print the next setting, ASF INSTALLED along with the first option, NO. If the ASF is not installed the option should read NO. If the ASF is installed, the option should be YES. Press the FF button until it prints the correct setting. Once the printer prints the correct setting, press the LF button once.®®16. The printer will print the next setting, SELECT IN SIGNAL FIXED along with the first option, YES. If the SELECT IN SIGNAL FIXED is not set to YES, press the FF button until it does. Once the printer prints SELECT IN SIGNAL FIXED YES, press the SELECT button once. This will save all current Memory Mode settings, exit Memory Mode, and return the printer to normal operation in Select status.®®The printer is now set correctly to work with PowerPrint.
Alps Allegro 500 True True DM P, S opt LQ False False I This card provides you with detailed instructions for setting the Memory Mode for the printer’s parallel interface to work with PowerPrint. The following settings will be made: Form length, Character Set, Print Variation, Top-of-form, Line Spacing, 1-inch Perforation Skip, Auto Tear Bar, Automatic LF, Detect Paper Out, International Character Set, Audible Buzzer, Print Direction for Graphics, Interface and Select In Signal Fixed.®®Note: In this card we will be giving you step-by-step instructions for defining a macro. We will be setting macro 1. By saving these selections to macro 1, the printer will automatically default to them upon power up. These settings can be made to any one of the three (3) macros, however if you decide to save these changes to any macro other than number 1, this macro will have to be loaded when the printer is turned on. For more detailed information on using MacroMind, refer to chapter 4 of the printer manual.®®Note: The LF and the SET TOF buttons are the same buttons. The FF and SET TOF buttons are the same buttons. The PITCH and the RESET buttons are the same buttons. The FONT and the TEAR BAR buttons are the same buttons.®®Note: When changing settings within a macro, the LF button always selects the next setting down. The FF button always selects the next option across. Pressing the LF button to select the next setting automatically saves the last option.®®Note: If you lose track at any time while setting MacroMind, the PITCH button takes you back to the previous setting, and the FONT button lets you skip forward three settings. Pressing either the PITCH or FONT button automatically saves the last option printed. At any point, pressing the SELECT button saves the current MacroMind settings and returns the printer to normal operation in Select status.®®Follow these instructions to define macro 1 and the Memory Mode using MacroMind.®®1. To enter MacroMind, first make sure the printer is properly loaded with paper and ribbon, and that the power is off. Then press and hold the SELECT button and turn the power on.®®Note: To ensure you enter MacroMind, hold down the SELECT button until the print head moves to the far left position, then let up on the SELECT button.®®The printer enters MacroMind and immediately prints out CHANGE MACRO SETTINGS.®®2. Press the LF button. The current settings for all three macros will print out.®®3. After printing out the macro settings, the printer prints MACRO SET SELECTION MACRO 1. Press the LF button twice and ensure the printer prints FORM LENGTH 11 INCHES. If the FORM LENGTH is not set to 11 INCHES, press the FF button until it does. Once the printer prints FORM LENGTH 11 INCHES, press the LF button once.®®4. The printer will print CHARACTER SET EPSON. If the CHARACTER SET is not set to EPSON, press the FF button until it does. Once the printer prints CHARACTER SET EPSON, press the LF button once.®®5. The printer will print PRINT VARIATION NORMAL. If the PRINT VARIATION is not set to NORMAL, press the FF button until it does. Once the printer prints PRINT VARIATION NORMAL, press the LF button once.®®6. The printer will print TOP-OF-FORM SETTING FIRST PRINT LINE. If the TOP-OF-FORM SETTING is not set to FIRST PRINT LINE, press the FF button until it does. Once the printer prints TOP-OF-FORM SETTING FIRST PRINT LINE, press the LF button once.®®7. The printer will print CHANGE NEXT MACRO. Press the FF button and the printer prints PRINT ALL MEMORY MODE SETTINGS.®®8. Press the LF button and the printer prints all the current Memory Mode settings.®®9. After printing all the current Memory Mode settings, the printer prints the first setting, LINE SPACING along with the first option, 6 LPI. If the LINE SPACING is not set to 6 LPI, press the FF button until it does. Once the printer prints LINE SPACING 6 LPI, press the LF button once.®®10. The printer will print the next setting,1-INCH PERFORATION SKIP along with the first option NO. If the 1-INCH PERFORATION SKIP is not set to NO, press the FF button until it does. Once the printer prints 1-INCH PERFORATION SKIP NO, press the LF button once.®®11. The printer will print the next setting, AUTO TEAR BAR along with the first option YES. If the AUTO TEAR BAR is not set to YES, press the FF button until it does. Once the printer prints AUTO TEAR BAR YES, press the LF button once.®®12. The printer will print the next setting, AUTOMATIC LF ON CARRIAGE RETURN along with the first option NO. If the AUTOMATIC LF ON CARRIAGE RETURN is not set to NO, press the FF button until it does. Once the printer prints AUTOMATIC LF ON CARRIAGE RETURN NO, press the LF button once.®®13. The printer will print the next setting, DETECT PAPER OUT along with the first option, YES. If the DETECT PAPER OUT is not set to YES, press the FF button until it does. Once the printer prints DETECT PAPER OUT YES, press the LF button once.®®14. The printer will print the next setting, INTERNATIONAL CHARACTER SET along with the first option, U.S.A. If the INTERNATIONAL CHARACTER SET is not set to U.S.A., press the FF button until it does. Once the printer prints INTERNATIONAL CHARACTER SET U.S.A., press the LF button twice.®®15. The printer will print the next setting, AUDIBLE BUZZER along with the first option, YES. If the AUDIBLE BUZZER is not set to YES, press the FF button until it does. Once the printer prints AUDIBLE BUZZER Yes, press the LF button once.®®16. The printer will print the next setting, PRINT DIRECTION FOR GRAPHICS along with the first option, BIDIRECTION. If the PRINT DIRECTION FOR GRAPHICS is not set to BIDIRECTION, press the FF button until it does. Once the printer prints PRINT DIRECTION FOR GRAPHICS BIDIRECTION, press the LF button twice.®®17. The printer will print the next setting, INTERFACE along with the first option, PARALLEL. If the INTERFACE is not set to PARALLEL, press the FF button until it does. Once the printer prints INTERFACE PARALLEL, press the LF button once.®®18. The printer will print the next setting, SELECT IN SIGNAL FIXED along with the first option, YES. If the SELECT IN SIGNAL FIXED is not set to YES, press the FF button until it does. Once the printer prints SELECT IN SIGNAL FIXED YES, press the SELECT button once. This will save all current MacroMind settings (Memory Mode and Macro Mode), exit MacroMind, and return the printer to normal operation in Select status.®®The printer is now set correctly to work with PowerPrint.
Alps Allegro 500XT True True DM P, S opt LQ False False R Alps@Allegro 500
Alps ALQ 218 True True DM/C P, S opt FX False False
Alps ALQ 224E True True DM/C P, S opt LQ False False I This card provides you with detailed instructions for setting the Memory Mode for the printer’s parallel interface to work with PowerPrint. The following settings will be made: Color, Line Spacing, Font Location, LQ Font Selection, Form Length, Print Line Width, Print Variation, 1-Inch Perforation Skip, Detect Paper Out, Extended Character Set, Fanfold Auto Load Position, Single Sheet Auto Load Position, Automatic LF on Carriage Return, International Character Set, Audible Buzzer, Print Direction for Graphics, Recognize Download Characters, and Select In Signal Fixed.®®Note: In this card we will be giving you step-by-step instructions for defining the Memory Mode. For more detailed information, refer to chapter 4 of the printer manual.®®Note: The NEXT OPTION and the LINE FEED buttons are the same buttons. The PREVIOUS OPTION and FORM FEED buttons are the same buttons. The MENU SELECT and the INSERT SHEET buttons are the same buttons.®®Note: When changing the Memory Mode settings, the NEXT OPTION button will change to the next possible setting of the current menu item list. To save the the setting of the current menu item and move to the next item on the menu, press the MENU SELECT button.®®Note: If you lose track at any time while setting the Memory Mode, press the ON-LINE button, which returns the printer to On-Line status, and start over. If you press the PREVIOUS OPTION button, the setting of the current menu item will be changed to the previous setting on the list.®®Follow these instructions to set the Memory Mode:®®1. To enter Memory Mode, first make sure the printer is properly loaded with paper and ribbon, and that the power is on. Then press the ON-LINE button to change the printer to Off-Line status.®®2. Press the ON-LINE and RESET buttons simultaneously to enter Memory Mode, the printer prints the first menu item COLOR, and its current setting, BLACK.®®Note: If you press the ON-LINE and RESET buttons again, the printer will print the entire Memory Mode items, each with its current setting. It will then print the first menu item (Color) again, with its current setting®®If COLOR is not set to BLACK press the NEXT OPTION button until is does. Once the printer prints COLOR BLACK, press the MENU SELECT button twice.®®3. The printer will print the third menu item, LINE SPACING along with the current setting, 6 LPI. If the LINE SPACING is not set to 6 LPI, press the NEXT OPTION button until it does. Once the printer prints LINE SPACING 6 LPI, press the MENU SELECT button twice.®®4. The printer will print the fifth menu item, FONT LOCATION along with the current setting, INTERNAL FONT. If the FONT LOCATION is not set to INTERNAL FONT, press the NEXT OPTION button until it does. Once the printer prints FONT LOCATION INTERNAL FONT, press the MENU SELECT button once.®®5. The printer will print the next menu item, LQ FONT SELECTION along with the current setting, FONT-1. If the LQ FONT SELECTION is not set to FONT-1, press the NEXT OPTION button until it does. Once the printer prints LQ FONT LOCATION FONT-1, press the MENU SELECT button once.®®6. The printer will print the next menu item, FORM LENGTH along with the current setting, 11 INCHES. If the FORM LENGTH is not set to 11 INCHES, press the NEXT OPTION button until it does. Once the printer prints FORM LENGTH 11 INCHES, press the MENU SELECT button once.®®7. The printer will print the next menu item, PRINT LINE WIDTH along with the current setting, 13.6 INCHES. If the PRINT LINE WIDTH is not set to 13.6 INCHES, press the NEXT OPTION button until it does. Once the printer prints PRINT LINE WIDTH WIDTH 13.6 INCHES, press the MENU SELECT button once.®®8. The printer will print the next menu item, PRINT VARIATION along with the current setting, NORMAL. If the PRINT VARIATION is not set to NORMAL, press the NEXT OPTION button until it does. Once the printer prints PRINT VARIATION NORMAL, press the MENU SELECT button once.®®9. The printer will print the next menu item, 1-INCH PERFORATION SKIP along with the current setting, NO. If the 1-INCH PERFORATION SKIP is not set to NO, press the NEXT OPTION button until it does. Once the printer prints 1-INCH PERFORATION SKIP NO, press the MENU SELECT button once.®®10. The printer will print the next menu item, DETECT PAPER OUT along with the current setting, YES. If the DETECT PAPER OUT is not set to YES, press the NEXT OPTION button until it does. Once the printer prints DETECT PAPER OUT YES, press the MENU SELECT button once.®®11. The printer will print the next menu item, EXTENDED CHARACTER SET along with the current setting, EPSON. If the EXTENDED CHARACTER SET is not set to EPSON, press the NEXT OPTION button until it does. Once the printer prints EXTENDED CHARACTER SET EPSON, press the MENU SELECT button once.®®12. The printer will print the next menu item, FANFOLD AUTO LOAD POSITION along with the current setting, TRACTOR. If the FANFOLD AUTO LOAD POSITION is not set to TRACTOR, press the NEXT OPTION button until it does. Once the printer prints FANFOLD AUTO LOAD POSITION TRACTOR, press the MENU SELECT button once.®®13. The printer will print the next menu item, SINGLE SHEET AUTO LOAD POSITION along with the current setting, PAPER BAIL. If the SINGLE SHEET AUTO LOAD POSITION is not set to PAPER BAIL, press the NEXT OPTION button until it does. Once the printer prints SINGLE SHEET AUTO LOAD POSITION PAPER BAIL, press the MENU SELECT button twice.®®14. The printer will print the sixteenth menu item, AUTOMATIC LF ON CARRIAGE RETURN along with the current setting, NO. If the AUTOMATIC LF ON CARRIAGE RETURN is not set to NO, press the NEXT OPTION button until it does. Once the printer prints AUTOMATIC LF ON CARRIAGE RETURN NO, press the MENU SELECT button once.®®15. The printer will print the next menu item, INTERNATIONAL CHARACTER SET along with the current setting, U.S.A. If the INTERNATIONAL CHARACTER SET is not set to U.S.A., press the NEXT OPTION button until it does. Once the printer prints INTERNATIONAL CHARACTER SET U.S.A., press the MENU SELECT button twice.®®16. The printer will print the next menu item, AUDIBLE BUZZER along with the current setting, YES. If the AUDIBLE BUZZER is not set to YES, press the NEXT OPTION button until it does. Once the printer prints AUDIBLE BUZZER YES, press the MENU SELECT button once.®®17. The printer will print the next menu item, PRINT DIRECTION FOR GRAPHICS along with the current setting, BIDIRECTION. If the PRINT DIRECTION FOR GRAPHICS is not set to BIDIRECTION, press the NEXT OPTION button until it does. Once the printer prints PRINT DIRECTION FOR GRAPHICS, press the MENU SELECT button once.®®18. The printer will print the next menu item, RECOGNIZE DOWNLOAD CHARACTERS along with the current setting, NO. If the RECOGNIZE DOWNLOAD CHARACTERS is not set to NO, press the NEXT OPTION button until it does. Once the printer prints RECOGNIZE DOWNLOAD CHARACTERS NO, press the MENU SELECT button once.®®19. The printer will print the next menu item, SELECT IN SIGNAL FIXED along with the current setting, YES. If the SELECT IN SIGNAL is not set to YES, press the NEXT OPTION button until it does. Once the printer prints SELECT IN SIGNAL YES, press the ON-LINE button. The printer will save the Memory Mode settings, issue a form feed and return to On-Line status.®®The printer is now set correctly to work with PowerPrint.
Alps ALQ 3001 True True DM/C P, S opt FX False False
Alps ASP 1000 True True DM P, S opt FX False False R U208100160DS1,1110000008275160DS2,00001100
Alps ASP 1600 True True DM P, S opt FX False False D U208100160DS1,1110000008275160DS2,00001100
Alps DMX 800 True True DM/C S, P FX False False
Alps LPX 600 True False L S, P LJ False False
Alps LPX 2020 True True L S, P LJ II False False
Alps LSX 1000 True True L P, S LJ IV False False
Alps LSX 1600 True True L S, P LJ II False False
Alps P2000+ True True DM P, S opt FX False False I This card provides you with detailed instructions for setting the Memory Mode for the printer’s parallel interface to work with PowerPrint. The following settings will be made: Line Spacing, Font Location, LQ Font Selection, HRI, Auto Tear Bar, Form Length, Print Line Width, Print Variation, 1-Inch Perforation Skip, Detect Paper Out, Extended Character Set, Command Code Set, Automatic LF on Carriage Return, International Character Set, Audible Buzzer, Recognize Download Characters, Interface, and Select-In Signal Fixed®®Note: In this card we will be giving you step-by-step instructions for defining the Memory Mode. For more detailed information, refer to chapter 3 of the Alps P2000+ manual.®®Note: The NEXT OPTION and the LF buttons are the same buttons. The PREVIOUS OPTION and FF buttons are the same buttons. The MENU SELECT and the INSERT buttons are the same buttons.®®Note: When changing the Memory Mode settings, the NEXT OPTION button will change to the next possible setting of the current menu item list. To save the the setting of the current menu item and move to the next item on the menu, press the MENU SELECT button.®®Note: If you lose track at any time while setting the Memory Mode, press the ON-LINE button, which returns the printer to On-Line status, and start over. If you press the PREVIOUS OPTION button, the setting of the current menu item will be changed to the previous setting on the list.®®Follow these instructions to set the Memory Mode:®®1. To enter Memory Mode, first make sure the printer is properly loaded with paper and ribbon, and that the power is on. Then press the ON-LINE button to change the printer to Off-Line status.®®2. Press the ON-LINE and RESET buttons simultaneously to enter Memory Mode, the printer prints the first menu item CHARACTER PITCH, and its current setting.®®Note: While the printer is in Memory Mode, you can work with the front cover open for better visibility.®®3. Press the MENU SELECT button three times and the printer will print the fourth menu item, FONT LOCATION along with the current setting, INTERNAL FONT. If the FONT LOCATION is not set to INTERNAL FONT, press the NEXT OPTION button until it does. Once the printer prints FONT LOCATION INTERNAL FONT, press the MENU SELECT button once.®®4. The printer will print the next menu item, LQ FONT SELECTION along with the current setting, FONT 1. If the LQ FONT SELECTION is not set to FONT 1, press the NEXT OPTION button until it does. Once the printer prints LQ FONT LOCATION FONT 1, press the MENU SELECT button once.®®5. The printer will print the next menu item, HRI along with the current setting, OFF. If HRI is not set to OFF, press the NEXT OPTION button until it does. Once the printer prints HRI OFF, press the MENU SELECT button once.®®6. The printer will print the next menu item, AUTO TEAR BAR along with the current setting, ON. If the AUTO TEAR BAR is not set to ON, press the NEXT OPTION button until it does. Once the printer prints AUTO TEAR BAR ON, press the MENU SELECT button once.®®7. The printer will print the next menu item, FORM LENGTH along with the current setting, 11 INCHES. If the FORM LENGTH is not set to 11 INCHES, press the NEXT OPTION button until it does. Once the printer prints FORM LENGTH 11 INCHES, press the MENU SELECT button once.®®8. The printer will print the next menu item, PRINT LINE WIDTH along with the current setting, 13.6 INCHES. If the PRINT LINE WIDTH is not set to 13.6 INCHES, press the NEXT OPTION button until it does. Once the printer prints PRINT LINE WIDTH WIDTH 13.6 INCHES, press the MENU SELECT button once.®®9. The printer will print the next menu item, PRINT VARIATION along with the current setting, NORMAL. If the PRINT VARIATION is not set to NORMAL, press the NEXT OPTION button until it does. Once the printer prints PRINT VARIATION NORMAL, press the MENU SELECT button once.®®10. The printer will print the next menu item, 1-INCH PERFORATION SKIP along with the current setting, NO. If the 1-INCH PERFORATION SKIP is not set to NO, press the NEXT OPTION button until it does. Once the printer prints 1-INCH PERFORATION SKIP NO, press the MENU SELECT button once.®®11. The printer will print the next menu item, DETECT PAPER OUT along with the current setting, YES. If the DETECT PAPER OUT is not set to YES, press the NEXT OPTION button until it does. Once the printer prints DETECT PAPER OUT YES, press the MENU SELECT button once.®®12. The printer will print the next menu item, EXTENDED CHARACTER SET along with the current setting, EPSON. If the EXTENDED CHARACTER SET is not set to EPSON, press the NEXT OPTION button until it does. Once the printer prints EXTENDED CHARACTER SET EPSON, press the MENU SELECT button once.®®13. The printer will print the next menu item, COMMAND CODE SET along with the current setting, EPSON. If the COMMAND CODE SET is not set to EPSON, press the NEXT OPTION button until it does. Once the printer prints COMMAND CODE SET EPSON, press the MENU SELECT button once.®®14. The printer will print the next menu item, TYPE OF AUTOMATIC SHEET FEEDER along with the current setting, DEMAND. If you are not using a sheet feeder, press the MENU SELECT button. If you are using one of the two available automatic sheet feeders, you must set the TYPE OF AUTOMATIC SHEET FEEDER to match the sheet feeder you are using. Once this menu item has been set, press the MENU SELECT button once.®®15. The printer will print the next menu item, AUTOMATIC LF ON CARRIAGE RETURN along with the current setting, NO. If the AUTOMATIC LF ON CARRIAGE RETURN is not set to NO, press the NEXT OPTION button until it does. Once the printer prints AUTOMATIC LF ON CARRIAGE RETURN NO, press the MENU SELECT button once.®®16. The printer will print the next menu item, INTERNATIONAL CHARACTER SET along with the current setting, U.S.A. If the INTERNATIONAL CHARACTER SET is not set to U.S.A., press the NEXT OPTION button until it does. Once the printer prints INTERNATIONAL CHARACTER SET U.S.A., press the MENU SELECT button twice.®®17. The printer will print the next menu item, AUDIBLE BUZZER along with the current setting, YES. If the AUDIBLE BUZZER is not set to YES, press the NEXT OPTION button until it does. Once the printer prints AUDIBLE BUZZER YES, press the MENU SELECT button once.®®18. The printer will print the next menu item, RECOGNIZE DOWNLOAD CHARACTERS along with the current setting, NO. If the RECOGNIZE DOWNLOAD CHARACTERS is not set to NO, press the NEXT OPTION button until it does. Once the printer prints RECOGNIZE DOWNLOAD CHARACTERS NO, press the MENU SELECT button once.®®19. The printer will print the next menu item, INTERFACE along with the current setting, PARALLEL. If the INTERFACE is not set to PARALLEL, press the NEXT OPTION button until it does. Once the printer prints INTERFACE PARALLEL, press the MENU SELECT button once.®®20. The printer will print the next menu item, SELECT-IN SIGNAL FIXED along with the current setting, YES If the SELECT-IN SIGNAL is not set to YES, press the NEXT OPTION button until it does. Once the printer prints SELECT-IN FIXED YES, press the ON-LINE button. The printer will save the Memory Mode settings, issue a form feed and return to On-Line status.®®The printer is now set correctly to work with PowerPrint.
Alps P2100 True True DM S, P FX False False D U408025160DS1,0000000008185160DS2,0000000008345160DS3,0000000010185225Interface Cart.,0000000011
Alps P2400 C True True DM/C S, P LQ False False I This card provides you with detailed instructions for setting the Memory Mode for the printer’s parallel interface to work with PowerPrint. The following settings will be made: Color, Line Spacing, Font Location, Form Length, Print Line Width, Print Variation, 1-Inch Perforation Skip, Detect Paper Out, Command Code Set, Automatic LF on Carriage Return, International Character Set, Audible Buzzer, Print Direction for Graphics, Interface, and Select In Signal Fixed.®®Note: In this card we will be giving you step-by-step instructions for defining the Memory Mode. For more detailed information, refer to chapter 2 of the Alps P2400C manual.®®Note: The NEXT OPTION and the LINE FEED buttons are the same buttons. The PREVIOUS OPTION and FORM FEED buttons are the same buttons. The MENU SELECT and the INSERT SHEET buttons are the same buttons.®®Note: When changing the Memory Mode settings, the NEXT OPTION button will change to the next possible setting of the current menu item list. To save the the setting of the current menu item and move to the next item on the menu, press the MENU SELECT button.®®Note: If you lose track at any time while setting the Memory Mode, press the ON-LINE button, which returns the printer to On-Line status, and start over. If you press the PREVIOUS OPTION button, the setting of the current menu item will be changed to the previous setting on the list.®®Follow these instructions to set the Memory Mode:®®1. To enter Memory Mode, first make sure the printer is properly loaded with paper and ribbon, and that the power is on. Then press the ON-LINE button to change the printer to Off-Line status.®®2. Press the Memory Mode button. The printer will print a menu of all the Memory Mode selections and the current setting for each on. Below the menu, the printer will print the first menu item COLOR, and its current setting, BLACK. If COLOR is not set to BLACK press the NEXT OPTION button until is does. Once the printer prints COLOR BLACK, press the MENU SELECT button twice.®®3. The printer will print the third menu item, LINE SPACING along with the current setting, 6 LPI. If the LINE SPACING is not set to 6 LPI, press the NEXT OPTION button until it does. Once the printer prints LINE SPACING 6 LPI, press the MENU SELECT button twice.®®4. The printer will print the fifth menu item, FONT LOCATION along with the current setting, INTERNAL FONT. If the FONT LOCATION is not set to INTERNAL FONT, press the NEXT OPTION button until it does. Once the printer prints FONT LOCATION INTERNAL FONT, press the MENU SELECT button once.®®5. The printer will print the next menu item, FORM LENGTH along with the current setting, 11 INCHES. If the FORM LENGTH is not set to 11 INCHES, press the NEXT OPTION button until it does. Once the printer prints FORM LENGTH 11 INCHES, press the MENU SELECT button once.®®6. The printer will print the next menu item, PRINT LINE WIDTH along with the current setting, 13.6 INCHES. If the PRINT LINE WIDTH is not set to 13.6 INCHES, press the NEXT OPTION button until it does. Once the printer prints PRINT LINE WIDTH WIDTH 13.6 INCHES, press the MENU SELECT button once.®®7. The printer will print the next menu item, PRINT VARIATION along with the current setting, NORMAL. If the PRINT VARIATION is not set to NORMAL, press the NEXT OPTION button until it does. Once the printer prints PRINT VARIATION NORMAL, press the MENU SELECT button once.®®8. The printer will print the next menu item, 1-INCH PERFORATION SKIP along with the current setting, NO. If the 1-INCH PERFORATION SKIP is not set to NO, press the NEXT OPTION button until it does. Once the printer prints 1-INCH PERFORATION SKIP NO, press the MENU SELECT button once.®®9. The printer will print the next menu item, DETECT PAPER OUT along with the current setting, YES. If the DETECT PAPER OUT is not set to YES, press the NEXT OPTION button until it does. Once the printer prints DETECT PAPER OUT YES, press the MENU SELECT button once.®®10. The printer will print the next menu item, COMMAND CODE SET along with the current setting EPSON MODE. If the COMMAND CODE SET is not set to EPSON MODE, press the NEXT OPTION button until it does. Once the printer prints COMMAND CODE SET EPSON MODE, press the MENU SELECT button once.®®11. The printer will print the next menu item, AUTOMATIC LF ON CARRIAGE RETURN along with the current setting, NO. If the AUTOMATIC LF ON CARRIAGE RETURN is not set to NO, press the NEXT OPTION button until it does. Once the printer prints AUTOMATIC LF ON CARRIAGE RETURN NO, press the MENU SELECT button once.®®12. The printer will print the next menu item, INTERNATIONAL CHARACTER SET along with the current setting, U.S.A. If the INTERNATIONAL CHARACTER SET is not set to U.S.A., press the NEXT OPTION button until it does. Once the printer prints INTERNATIONAL CHARACTER SET U.S.A., press the MENU SELECT button twice.®®13. The printer will print the fifteenth menu item, AUDIBLE BUZZER along with the current setting, YES. If the AUDIBLE BUZZER is not set to YES, press the NEXT OPTION button until it does. Once the printer prints AUDIBLE BUZZER YES, press the MENU SELECT button once.®®14. The printer will print the next menu item, PRINT DIRECTION FOR GRAPHICS along with the current setting, BIDIRECTION. If the PRINT DIRECTION FOR GRAPHICS is not set to BIDIRECTION, press the NEXT OPTION button until it does. Once the printer prints PRINT DIRECTION FOR GRAPHICS, press the MENU SELECT button once.®®15. The printer will print the next menu item, INTERFACE along with the current setting, PARALLEL. If the INTERFACE is not set to PARALLEL, press the NEXT OPTION button until it does. Once the printer prints INTERFACE PARALLEL, press the MENU SELECT button once.®®16. The printer will print the next menu item, SELECT IN SIGNAL FIXED along with the current setting, YES. If the SELECT IN SIGNAL FIXED is not set to YES, press the NEXT OPTION button until it does. Once the printer prints SELECT IN SIGNAL YES, press the ON-LINE button. The printer will save the Memory Mode settings, issue a form feed and return to On-Line status.®®The printer is now set correctly to work with PowerPrint.
Alps P2418 True True DM/C S, P FX False False
Alps P2424 C True True DM/C S, P LQ False False
Anzak 2600 True True DM S, P FX True False
Anzak 3018 True False L P LJ False False
Apple Portable StyleWriter True False IJ P BJ False True
AT&T 477 True True DM/C S, P FX False False
AT&T 495 True False L S, P LJ False False
AT&T 570 True True DM P FX False False
AT&T 571 True True DM P FX False False
AT&T 577 True True DM/C S, P FX False False
AT&T 580 True True DM P, S opt LQ False False
AT&T 581 True True DM P, S opt LQ False False
AT&T 583 True True DM/C S, P LQ False False
AT&T 593 True True L S, P LJ II False False
AT&T 595 True True L S, P LJ II False False
Axonix LiteWrite True True DM S, P FX False False
Axonix MilWrite True True DM P, S opt FX False False
Axonix ThinWrite 100 True True DM S, P FX False False
BDT Products ErgoPrint 310 True False IJ S, P DJ False False
BDT Products ErgoPrint 510 True True L S, P LJ II False False
BDT Products ErgoPrint 610 True False L S, P LJ True False
BDT Products ErgoPrint 610 II True True L S, P LJ II False False
BGL Technology Mark 9115-3 True True L S, P LJ II False False
BGL Technology Mark 9115-4 True True L S, P LJ II False False
BGL Technology Mark 9120-3D True True L S, P LJ II False False
BGL Technology Mark 9120-3S True True L S, P LJ II False False
BGL Technology Mark 9120-4D True True L P, S LJ II False False
BGL Technology Mark 9120-4S True True L P, S LJ II False False
BGL Technology Mark 9120-8D True True L S, P LJ II False False
BGL Technology Mark 9120-8S True True L S, P LJ II False False
BGL Technology Mark I True True L S or P LJ II False False Parallel interface required.
BGL Technology Mark I Plus True True L S or P LJ II False False Parallel interface required.
BGL Technology Mark I T True True L S or P LJ II False False Parallel interface required.
BGL Technology Mark II True True L S or P LJ II False False Parallel interface required.
BGL Technology Mark III True True L S or P LJ II False False Parallel interface required.
BGL Technology Mark IV True True L S or P LJ II False False Parallel interface required.
Blaser Industries Blaserstar True False L S, P LJ False False
Blaser Industries Blaserstar 2 True True L S or P LJ II True False Parallel interface required.
BottomLine Technologies BT 5015 True True L S, P LJ II False False
BottomLine Technologies BT 5106 True True L S, P LJ II False False
Brother HJ-100i True False IJ P BJ False False
Brother HL-4 True True L S, P LJ IIP False True
Brother HL-4V True True L S, P LJ III False False
Brother HL-4Ve True True L P, S LJ III False False
Brother HL-6 True True L P, S LJ III False False
Brother HL-6V True True L P, S LJ III False False
Brother HL-8 True False L S, P LJ False True
Brother HL-8e True True L S, P LJ II False True
Brother HL-8V True True L S, P LJ III False False
Brother HL-10H True True L P, S LJ IV False False
Brother HL-10V True True L S, P LJ III False False
Brother M-1109 True True DM FX False True
Brother M-1209 True True DM P FX False True
Brother M-1309 True True DM P, S opt FX False True
Brother M-1809 True True DM/C S, P FX False True I The following settings will be made: Epson emulation, parallel interface, no skip-over perforation, and no auto LF.®®Turn your printer on to confirm or set your control panel settings.®®Note: The “*” at the LCD display indicates the current setting.®®Note: Pressing the forward button or backward button displays the FUNCTION setting for each item. (You also have to press the SET switch to save the selection but we will include this step in the following instructions.) If you lose track at any time while setting the control panel, press the ITEM or MENU switch to go back to the menu of a previous level (in all instances will have to press it more than once).®®Note: The MENU and the ON LINE switches are the same switches. The ITEM and LF switches are the same switches. The forward button and the TOF button are the same buttons. The backward and the EJECT button are the same buttons. The SET and the LOAD switches are the same switches. The QUIT and FUNCTION switches are the same switches.®®Note: If optional SF-240/250 (Auto Cut Sheet Feeder) is installed, press the ON LINE switch to take the printer off line, and press the LOAD switch until the LCD reads ACSF. This selects ACSF (Auto Cut Sheet Feeder mode).®®1. Press the ON LINE switch once to take the printer off line.®®2. Press the FUNCTION switch once so the LCD displays FONT MENU.®®3. Press the MENU switch twice and make sure the LCD reads EMULATE MENU.®®4. Press the ITEM switch and ensure the LCD reads EMULATE EPSON*. If the LCD does not read EMULATE EPSON* use the forward button to change this item. Once the LCD reads EMULATE EPSON* press the SET switch to save this setting.®®5. Press the MENU switch once so the LCD reads I/F MENU.®®6. Press the ITEM switch once and ensure the LCD reads I/F Parallel*. If the LCD does not read I/F Parallel* use the forward button to change this item. Once the LCD reads I/F Parallel* press the SET switch to save this setting.®®7. Press the MENU switch once and ensure the LCD reads FORMAT MENU.®®8. Press the ITEM switch four (4) or six (6) and ensure the LCD reads SKIP-PER NO*. If the LCD does not read SKIP-PER NO* use the forward button to change this item. Once the LCD reads SKIP-PER NO* press the SET switch to save this setting.®®9. Press the ITEM switch once and ensure the LCD reads AUTO LF NO*. If the LCD does not read AUTO LF NO* use the forward button to change this item. Once the LCD reads AUTO LF NO* press the SET switch to save this setting.®®10. Press the QUIT switch and the LCD will display the current Switch Panel settings. Press the ON LINE switch the turn the printer on line.®®The printer is now set correctly to work with PowerPrint.
Brother M-1824L True True DM/C S, P LQ False True R Brother@M-1809
Brother M-1909 True True DM/C S, P FX False True R Brother@M-1809
Brother M-1924L True True DM/C S, P LQ False True R Brother@M-1809
Brother M-2518 True True DM/C P, S opt FX False False
Bull CompuPrint 4/66 True True DM/C P, S opt FX False False
Bull CompuPrint 4/68 True True DM/C P, S opt FX False False
Bull CompuPrint 970 True True DM/C S, P FX False False
Bull LP-230 True True L S, P LJ IIP False False
Bull PageMaster 1025 True True L P, S LJ III False False
Bull PageMaster 201 True False IJ P, S opt DJ False False
Bull PageMaster 1021 True True L S, P LJ IIP False False
Bull PageMaster 1725 True True L P, S LJ IV False False
C. Itoh/C-Tech 9500 True True DM/C S or P FX False False Parallel interface required.
C. Itoh/C-Tech 9515 True True DM/C S or P FX False False Parallel interface required.
C. Itoh/C-Tech 9715 True True DM/C P, S opt LQ False False
C. Itoh/C-Tech C-240 True True DM S, P FX False False
C. Itoh/C-Tech C-245 True True DM S, P FX False False
C. Itoh/C-Tech C-310 True True DM/C S or P FX True True Parallel interface required.
C. Itoh/C-Tech C-315 True True DM/C S or P FX True True Parallel interface required.
C. Itoh/C-Tech C-410 True True DM P, S opt FX False False
C. Itoh/C-Tech C-415 True True DM P, S opt FX False False
C. Itoh/C-Tech C-420 True True DM P, S opt FX False False
C. Itoh/C-Tech C-425 True True DM P, S opt LQ False False
C. Itoh/C-Tech C-510 True True DM S or P LQ False False Parallel interface required.
C. Itoh/C-Tech C-515 True True DM S or P LQ False False Parallel interface required.
C. Itoh/C-Tech C-610 True True DM S, P LQ False False
C. Itoh/C-Tech C-610 + True True DM S, P LQ False False
C. Itoh/C-Tech C-610C + True True DM/C S, P LQ False False
C. Itoh/C-Tech C-610III True True DM P, S LQ False False
C. Itoh/C-Tech C-645 True True DM/C S, P FX False False
C. Itoh/C-Tech C-715 A True True DM S, P LQ False False
C. Itoh/C-Tech CI-4 True True L S, P LJ IIP False False
C. Itoh/C-Tech CI-8 True True L S, P LJ III False False
C. Itoh/C-Tech CI-8E True True L S, P LJ III False False
C. Itoh/C-Tech CI-8XTRA True True L P, S LJ II False False
C. Itoh/C-Tech Jet-Setter True False L S, P LJ False False
C. Itoh/C-Tech ProWriter C-240 True True DM FX False False
C. Itoh/C-Tech ProWriter C-245 True True DM FX False False
C. Itoh/C-Tech ProWriter C-310 CXP True True DM/C FX True False
C. Itoh/C-Tech ProWriter C-610II True True DM P, S LQ False False
C. Itoh/C-Tech ProWriter C-615II True True DM P, S LQ False False
C. Itoh/C-Tech SpeedJet CJ-300 True True IJ P LJ II False False
CAF Computer Corp CAF Laser True True L S, P LJ II False False
CAF Computer Corp Syslaser True True L S, P LJ II False False
CalComp 5902 True True L S, P FX False False
Canon BJ-5 True True IJ P BJ False False
Canon BJ-10e True True IJ P BJ False True D U110170160,0000000000 If you have the sheet feeder for the BJ-10e printer switch number 1 (leftmost) should be up.
Canon BJ-10ex True True IJ P BJ False False D U111168160,00000000000 If you have the sheet feeder for the BJ-10ex printer switch number 1 (leftmost) should be up.
Canon BJ-10sx True False IJ P BJ False False
Canon BJ-20 True True IJ P BJ False False D U112168160,100000000000 If you have a sheet feeder installed, make sure that the appropriate dip switch is set correctly so that your printer can access it. See you printer manual for details.
Canon BJ-200 True True IJ P BJC-600 False False D U112168160,111111111110
Canon BJ-230 True True IJ P BJ-330 False False R Canon@BJ-200
Canon BJ-300 True True IJ P, S opt BJ-330 False True D D208100160SW1,0011010110275160SW2,1111111111 If you have a sheet feeder set dip switch 7 on SW1 to the up position (off).
Canon BJ-330 True True IJ P, S opt BJ-330 False True R Canon@BJ-300
Canon BJC-600 True False IJ/C P BJC-600 False True D U112160160,000000000001
Canon BJC-800 True True IJ/C P BJC-600 False False
Canon BJC-820 True True IJ/C P BJC-600 False False
Canon LBP-4 True True L S, P LBP False True I Turn your printer on to confirm or set your control panel settings.®®Note: The “=” at the LCD display indicates the current setting.®®Note: If you need to change a setting, press the right arrow key to toggle through the available options in the LCD display. (You also have to press the ENTER key to save the selection but we will include this step in the following instructions.) If you lose track at any time while setting the control panel, press the up arrow key to go back to the menu of a previous level (in some instances you may have to press it more than once).®®Note: The ENTER and the down arrow keys are the same key. The MENU and right arrow keys are the same key.®®1. Press the ON LINE key once to take the printer off line.®®2. Press the MENU key six times until the LCD reads INTERFACE SAVE->.®®3. Press the down arrow key twice and make sure the LCD reads i/f =CENTRO. (If the display reads i/f =RS232C, press the right arrow key to select CENTRO.) ®®4. Press the up arrow key once and the LCD will read INTERFACE ...®®5. Press the right arrow key twice and the LCD will read SAVE->NVRAM LOAD.®®6. Press the down arrow key once and the LCD will flash OK then read SAVE->NVRAM LOAD.®®7. Press the ON LINE key and the LCD will read 00 READY.®®Your printer is now set to work correctly with PowerPrint.
Canon LBP-4 Lite True True L P LBP False False
Canon LBP-4 Plus True True L S, P LBP False False R Canon@LBP-4
Canon LBP-4 sx True True L P, S LJ II False False
Canon LBP-8III True True L S, P LBP False True R Canon@LBP-4
Canon LBP-8III Plus True True L S, P LBP False False R Canon@LBP-4
Canon LBP-8III R True True L S, P LBP False True R Canon@LBP-4
Canon LBP-8III T True True L S, P LBP False True R Canon@LBP-4
Canon LBP-8IV True True L P, S LBP False False
Canon LBP-8 sx True True L P, S LJ III False False
Canon LBP-430 True True L P LJ III False False
Casio LCS 240 True True L S, P FX False False
Casio LCS 300 True True L S, P FX False False
CIE America CI-4000 True True DM S, P FX False False
CIE America CI-5000 True True DM/C S, P FX False True
CIE Terminals Lips 10 True False L S, P LJ False False
Citizen 120D True True DM P, S opt FX False True
Citizen 120D+ True True DM P, S opt FX False False
Citizen 180D True True DM P, S opt FX False True
Citizen 200GX True True DM/C P, S opt FX False True
Citizen 200GX Fifteen True True DM/C P, S opt FX False False
Citizen GSX-140 True True DM/C P, S opt LQ False True I This card provides you with detailed instructions for setting macro 1 in the Command-Vue Setup Menu for the Citizen GSX 140 printer using the parallel interface. The following settings will be made: Epson emulation, copy mode off, text printing direction bi-directional, graphics printing direction uni-directional, software command lock off, line spacing 6 LPI, form length 11 inches, page skip off, ribbon either normal or color, automatic sheet feeder on or off, auto line feed off, and select in signal ignore.®®Note: In these instructions we will be giving you step-by-step instructions for defining a Command-Vue macro. We will be setting macro 1 in order to save any possible changes. By saving these selections to macro 1, the printer will automatically default to them upon power up. These settings can be made to any one of the four (4) macros, however if you decide to save these changes to any macro other than number 1, this macro will have to be loaded when the printer is turned on. For more detailed information on defining a Command-Vue macro see page 129 in the Citizen GSX 140 user’s manual. For more detailed information on using the Command-Vue Setup Menu refer to chapter six (6) in the Citizen GSX 140 user’s manual®®Note: Pressing the JUMP key to move to the next jump point. Press the MENU key to move to the next menu. Press the SELECT key to move to the next selection.®®Note: If you lose track at any time while setting the Command-Vue Setup Menu, while holding down the PARK LOAD key, press the MENU key to move to the previous menu or while holding down the PARK LOAD key, press the SELECT key to scroll to the previous selection®®Note: The MENU and the PITCH keys are the same keys. The SAVE and LOAD MACRO keys are the same keys. The PARK LOAD and the FONT keys are the same keys. The SELECT and the QUICK keys are the same keys. The JUMP and the LF/FF COLOR keys are the same keys.®®Note: Changes are saved by pressing the SAVE key while the menu selection is displayed on the control panel. The first character will be underlined, indicating it is active.®®Note: The Factory Defaults contain all the correct settings for using the Citizen GSX 140 printer with PowerPrint. If you are a brave person and do not care about your current Command-Vue settings or macros, a very fast way to set macro 1 of the Command-Vue Setup Menu is to reset all settings to the Factory Defaults. Resetting the printer using this method will erase all four macros previously defined and change them all to the factory default selections. If you are using the color ribbon or sheet feeder, we recommend you do not use this method of setting the Command-Vue Setup Menu because the default settings do not activate these options To reset to the Factory Defaults:®®1. Take the printer off-line by pressing the ON LINE key.®®2. While holding down the SELECT key, press the ON LINE and PARK LOAD keys for more than three (3) seconds. The printer will display FACTORY INITIAL for two (2) seconds and then it will display OFF LINE.®®The Citizen GSX 140 printer is now set correctly to work with PowerPrint.®®If you are not that brave or you have the color ribbon and/or automatic sheet feeder installed, follow these instructions to set macro 1 of the Command-Vue Setup Menu:®®1. Assuming the printer is on, press the ON LINE key to take the printer off-line. The control panel will display OFF LINE.®®2. Press the MENU key once and the control panel will display PRNT OUT DEMO.®®3. Press the JUMP key once and the control panel will display MAC CTRL LOAD MAC.®®4. Press the MENU key once and the control panel will display MAC CTRL DEFN MAC.®®5. Press the SELECT key and the control panel will display DEFN MAC MACRO 1.®®6. Press the SAVE key and the control panel will display LOADED MACRO 1 for two (2) seconds and then changes to DEFN MAC MACRO 1.®®7. Press the JUMP key once until the control panel reads EMULATION.®®8. Press the SELECT key once and ensure the control panel reads EMULATION EPSON. If the control panel does not read EMULATION EPSON use the SELECT key to change this selection. Once the control panel reads EMULATION EPSON press the SAVE key to save this setting.®®9. Press the JUMP key two (2) times and the control panel will display PRN MODE CPY MODE.®®10. Press the SELECT key once and ensure the control panel displays CPY MODE OFF. If the control panel does not display OFF, press the SELECT key until it does. Once the control panel reads EPSON press the SAVE key to save this setting.®®11. Press the MENU key once and ensure the control panel displays PRN MODE TEXT DIR.®®12. Press the SELECT key once and ensure the control panel displays TEXT DIR BI DIR. If the control panel does not display BI DIR, press the SELECT key until it does. Once the control panel reads BI DIR press the SAVE key to save this setting.®®13. Press the MENU key once and ensure the control panel displays PRN MODE GRPH DIR.®®14. Press the SELECT key once and ensure the control panel displays GRPH DIR UNI DIR. If the control panel does not display UNI DIR, press the SELECT key until it does. Once the control panel reads UNI DIR press the SAVE key to save this setting.®®15. Press the MENU key once and ensure the control panel displays PRN MODE SW LOCK.®®16. Press the MENU key once and ensure the control panel displays SW LOCK OFF. If the control panel does not display OFF, press the SELECT key until it does. Once the control panel reads OFF press the SAVE key to save this setting.®®17. Press the JUMP key once and ensure the control panel displays PG LYOUT LINE SP.®®18. Press the SELECT key once and ensure the control panel displays LINE SP. 6 LPI. If the control panel does not display 6 LPI, press the SELECT key until it does. Once the control panel reads 6 LPI press the SAVE key to save this setting.®®19. Press the MENU key once and ensure the control panel displays PG LYOUT FRM LNTH.®®20. Press the SELECT key once and ensure the control panel displays FRM LNTH 11 INCH. If the control panel does not display 11 INCH, press the SELECT key until it does. Once the control panel reads 11 INCH press the SAVE key to save this setting.®®21. Press the MENU key once and ensure the control panel displays PG LYOUT PG SKIP.®®22. Press the SELECT key once and ensure the control panel displays PG SKIP OFF. If the control panel does not display OFF, press the SELECT key until it does. Once the control panel reads OFF press the SAVE key to save this setting.®®23. Press the JUMP key once and ensure the control panel displays INSTALL RIBBON.®®24. Press the SELECT key once and ensure the control panel displays RIBBON NORMAL. If you using the color ribbon the control panel display must be set to RIBBON COLOR. If the control panel does not display the correct selection, press the SELECT key until it does. Once the control panel displays the correct selection, press the SAVE key to save this setting.®®25. Press the MENU key once and ensure the control panel displays INSTALL A.S.F.®®26. Press the SELECT key once and ensure the control panel displays A.S.F. OFF. If the automatic cut sheet feeder is installed the display should read A.S.F. ON. If the control panel does not display the correct selection, press the SELECT key until it does. Once the control panel displays the correct selection, press the SAVE key to save this setting.®®27. Press the MENU key two (2) times and ensure the control panel displays INSTALL AUTO LF.®®28. Press the SELECT key once and ensure the control panel displays AUTO LF OFF. If the control panel does not display OFF, press the SELECT key until it does. Once the control panel reads OFF press the SAVE key to save this setting.®®29. Press the MENU key once and ensure the control panel displays INSTALL SLCT IN.®®30. Press the SELECT key once and ensure the control panel displays SLCT IN IGNORE. If the control panel does not display IGNORE, press the SELECT key until it does. Once the control panel reads IGNORE press the SAVE key to save this setting.®®31. Press the Save key again (or twice) and the control panel will display SAVE? MACRO 1.®®32. Press the Save key again and the control panel will display SAVED MACRO 3 for two (2) seconds and then displays OFF LINE>®®33. Press the ON LINE key sets the printer on-line.®®The Citizen GSX 140 printer is now set correctly to work with PowerPrint.
Citizen GSX-140 Plus True True DM/C P, S opt LQ False False
CPT Corporation LP-8 True False L S, P LJ False False
CPT Corporation LP-8GS True False L S, P LJ False False
CPT Corporation LP-15 True False L S, P LJ False False
CSS Laboratories OAW153 True True L P LJ II False False
CSS Laboratories OAW223 True True L P LJ II False False
CTSI International Infoscribe 1000 True True DM S or P FX False False Parallel interface required.
CTSI International Infoscribe 1100 True True DM S or P FX False False Parallel interface required.
Daisy Systems M7001 True True L S, P FX False False
Daisy Systems M8001 True True DM/C S or P LQ False False Parallel interface required.
Data General 6474 True False L S, P LJ False False
Data General 6475 True False L S, P LJ False False
Data General 6476 True False L S, P LJ False False
Data General 6477 True False L S, P LJ False False
Data General 6514 True True DM S, P LQ False False
Data General 6515 True True DM/C S, P LQ False False
Data General 6594 True True DM/C S, P FX False False
Data General 6640 True True L P, S opt LJ II False False
Data General 6640T True True L P, S opt LJ II False False
Data General 6771 True True L P, S opt LJ II False False
Data General 6772 True True L P, S opt LJ II False False
Data General 6773 True True L P, S opt LJ II False False
Data General 6789 True True DM S, P FX False False
Dataproducts 6298 True True DM P, S opt FX False False
Dataproducts 8500 True True DM S, P FX False False
Dataproducts 9030 True True DM P, S opt FX False False
Dataproducts 9034 True True DM S, P LQ False False
Dataproducts 9040 True True DM/C P, S opt FX False False
Dataproducts 9044 True True DM/C S, P LQ False False
Dataproducts Jolt True True IJ/C P, S LJ II False False
Dataproducts LX-455 True True DM P, S FX False False
Dataproducts LZR-650 True True L S, P LJ II False True I 1. Turn your printer on and press the ON LINE button to take your printer off-line. (ON LINE light should be off).®2. Press and hold the MENU button for approximately 7 seconds until the display changes and ensure it reads® SYM SET=ROMAN-8*®3. Press the MENU button, ensure the display reads ® I/F=PARALLEL* ®4. Press the MENU button and ensure the display reads ® EMULATION=HPLJ2*®5. Press the MENU button and ensure the display reads ® TRAY =LETTER*®6. Press the MENU button and ensure the display reads® COPIES=1*®7. Press the MENU button and ensure the display reads® FONT SOURCE=I*®8. Press the MENU button and ensure the display reads ® FONT NUMBER=00*®9. Press the MENU button and ensure the display reads® FORM LENGTH=60*®10. Press the ON LINE button key once to put the printer on-line.®®Your printer is now set to work correctly with PowerPrint.
Dataproducts LZR-1230 True False L S, P LJ False True
Dataproducts LZR-1555 True True L P, S LJ III False False
Dataproducts LZR-1650 True True L S, P LJ II False False
Dataproducts LZR-2450 True True L S, P LJ II False False
Dataproducts LZR-2450D True True L S, P LJ II False False
Dataproducts LZR-2455 True True L S, P LJ II False False
Dataproducts LZR-2455D True True L S, P LJ II False False
DataSource M7001 True False L S, P LJ False False
Datasouth 8/1080 True False L S, P LJ False False
Datasouth 8/3080 True True L S, P FX False False
Datasouth 8/5080 True True L S, P FX False False
Datasouth Documax A-3300 True True DM P, S FX False False
Datasouth Documax C-3300 True True DM P FX False False
Datasouth DS 400 True True DM S, P FX False False
Datasouth Performax A600 True True DM S, P FX False False
Datasouth XL 300 True True DM S, P FX False False
Datasouth XL 300 DD True True DM S, P FX False False
Datasouth XL 400 True True DM S, P FX False False
DEC DecJet 1000 True False IJ P DJ False False
DEC DecJet 2000 True False IJ P DJ False False
DEC DecLaser 1100 True True L P LBP True False
DEC DecLaser 1150 True True L P LBP True False
DEC DecLaser 2100 True True L P LBP True False
DEC DecLaser 2100 Plus True True L P LBP True False
DEC DecLaser 2150 True True L P LBP True False
DEC DecLaser 2150 Plus True True L P LBP True False
DEC DecLaser 2200 True True L P LBP True False
DEC DecLaser 2200 Plus True True L P LBP True False
DEC DecLaser 2250 True True L P LBP True False
DEC DecLaser 2250 Plus True True L P LBP True False
DEC DecLaser 3200 True True L P LJ II False False
DEC DecLaser 3250 True True L P LJ II False False
DEC DecWriter 95 True True DM/C P, S opt LQ False False
Decision Data 6415 True True L P FX False False
Derex S 3000II True True L S, P LJ II False False
Derex S 3030-2D True False L P, S LJ False False
Desktop Systems Laser Printer True True L S, P LJ II False False
Digital Design 616-MLP True True L S, P LJ II False False
Digital Design 636 True False L S, P LJ False False
Digital Design 656 Laser Check True True L S, P LJ II False False
Digital Design 656 Plus-MICR True True L S, P LJ II False False
Electronic Form Formwriter 2 True True L S, P LJ II False False
Electronic Form Formwriter 2E True True L S, P LJ II False False
Electronic Form Formwriter 2EX True True L S, P LJ II False False
Electronic Form Formwriter 2EXD/MX True True L S, P LJ II False False
Electronic Form Formwriter 2X True True L S, P LJ II False False
Electronic Form Formwriter 4 True True L S, P LJ II False False
Electronic Form Formwriter 8 True True L S, P LJ II False False
Electronic Form Formwriter 10 True True L S, P LJ II False False
Electronic Form Formwriter 10X True True L S, P LJ II False False
Electronic Form Formwriter 10XD True True L S, P LJ II False False
Epson ActionLaser True True L S, P LJ II False False
Epson ActionLaser 1000 True True L P, S opt LJ III False False
Epson ActionLaser 1500 True True L P, S LJ III False False
Epson ActionLaser II True True L S, P LJ IIP False False
Epson ActionLaser Plus True True L S, P LJ II False False
Epson ActionPrinter 3260 True False DM/C P ESC/P2 False False
Epson ActionPrinter AP-2000 True True DM P, S opt FX False False
Epson ActionPrinter AP-2500 True True DM P, S opt FX False False
Epson ActionPrinter T-1000 True True DM P, S opt FX False False
Epson Apex 80 True True DM P, S opt FX False False D U208100160SW1,0000011104275160SW2,0000 When using a sheet feeder set Dip switch 2 on SW2 to the "up" position (on).
Epson DFX-5000 True True DM S, P FX False True D U208100160SW1,0000011108275160SW2,00000000
Epson DFX-8000 True True DM S, P FX False True D U308050160SW 1-3,0000011108185160,0000000008320160,00000001
Epson EP-4000 True True IJ S, P LJ II False True
Epson EPL-5000 True True L P, S opt LJ IIP False False
Epson EPL-5200 True True L P, S LJ III False False
Epson EPL-6000 True True L S, P LJ II False True
Epson EPL-7000 True True L S, P LJ IIP False True I 1. Turn your printer on and press the ON LINE button to take your printer off-line. (The "ON LINE" light should be off).®®2. Press and hold the SelecType button down for about five seconds until the "Level 2" light goes on.®®3. Press the down arrow button or the up arrow button until the LCD display reads "FACTORY RESET" and press the right arrow button to select this setting. The LCD display should now show "EXE" on the right-hand side.®®4. Press the right arrow button. This will execute the selection and set your printer to the original factory defaults. After a short while, the ON LINE light will light up, indicating that the printer is ready to print.®®Your printer is now set to work correctly with PowerPrint.
Epson EPL-8000 True True L P or S LJ III False False Parallel port required.
Epson EX-800 True True DM P, S opt FX False True D U208100160SW1,0000011108275160SW2,00000000 Dip switch 2 on SW 2 should be "up" (on) when using a sheet feeder.
Epson EX-1000 True True DM S/DIN-6, P FX False True
Epson FX-80 True True DM P, S opt FX False True D U208100160SW1,0011011104275160SW2,1000
Epson FX-80 + True True DM P, S opt FX False False D U208100160SW1,0011011104275160SW2,1000 Dip switch 2 on SW 2 should be "up" (on) when using a sheet feeder.
Epson FX-85 True True DM P, S opt FX False True R Epson@FX-80 +
Epson FX-86e True True DM P, S opt FX False True R Epson@FX-286e
Epson FX-100 True True DM P, S opt FX False False D U208100160SW1,0011011104275160SW2,1000
Epson FX-100 + True True DM P, S opt FX False False R Epson@FX-80 +
Epson FX-185 True True DM P, S opt FX False False R Epson@FX-80 +
Epson FX-286 True True DM P, S opt FX False False D U208100160SW1,0011011104275160SW2,1000
Epson FX-286e True True DM P, S opt FX False True D U208100160SW1,0000011104275160SW2,0000 Dip switch 2 on SW 2 should be "up" (on) when using a sheet feeder.
Epson FX-850 True True DM P, S opt FX False True R Epson@FX-286e
Epson FX-870 True True DM P, S opt FX False False
Epson FX-1050 True True DM P, S opt FX False True R Epson@FX-286e
Epson FX-1170 True True DM P, S opt FX False False
Epson HS-80 True True DM P FX False False
Epson JX-80 True True DM/C P, S opt FX False False
Epson L-750 True True DM P, S opt LQ False True D U208100160SW1,1111100008275160SW2,00001100 Dip switch 8 on SW 1 should be "up" (on) when using a sheet feeder.
Epson L-1000 True True DM P, S opt LQ False True R Epson@L-750
Epson LQ-200 True True DM P, S opt LQ False True
Epson LQ-500 True True DM P, S opt LQ False True N U208100160SW1,1111100008275160SW2,00001100 Dip switch 8 on SW 1 should be "up" (on) when using a sheet feeder.
Epson LQ-510 True True DM P, S opt LQ False True D U208100160SW1,1111100008275160SW2,01001100 Dip switch 8 on SW 1 should be "up" (on) when using a sheet feeder.
Epson LQ-800 True True DM P, S opt LQ False True D U208100160SW1,1111100008275160SW2,00001110 Dip switch 8 on SW 1 should be "up" (on) when using a sheet feeder.
Epson LQ-850 True True DM S/DIN-6, P LQ False True D U208100160SW1,1110000008275160SW2,00001010 Dip switch 7 on SW 1 should be "up" (on) when using a sheet feeder.
Epson LQ-860 True True DM/C S, P LQ False True D U208100160SW1,1110010008275160SW2,00001010 Dip switch 7 on SW 1 should be "up" (on) when using a sheet feeder.
Epson LQ-950 True True DM S/DIN-6, P LQ False True R Epson@LQ-850
Epson LQ-1000 True True DM P, S opt LQ False True D U208100160SW1,1111100008275160SW2,00001110 Dip switch 8 on SW 1 should be "up" (on) when using a sheet feeder.
Epson LQ-1010 True True DM P, S opt LQ False True R Epson@LQ-510
Epson LQ-1050 True True DM S/DIN-6, P LQ False True R Epson@LQ-850
Epson LQ-1060 True True DM/C S, P LQ False False
Epson LQ-1070 True True DM P, S opt LQ False False D U208100160SW1,1110000004275160SW2,0000
Epson LQ-1500 True True DM P, S opt LQ False False D U208100160SW1,1000000008275160SW2,11100101
Epson LQ-2500 True True DM/C S/DIN-6, P LQ False True I PARALLEL MODE (step by step instructions not available)®®Set Macro 1 to:® Print Quality : Draft*® Font : Courier*® Pitch : 10 pitch*® Condensed : OFF*® Form Length : 11”*® 1” Skip over Perforation : OFF® Right Margin : 136® Left Margin : 0® Character Generator Table : Italic® Country : USA* ® Print Direction : Bidirectional® Half Speed : OFF® Sheet Feeder : OFF*® Default Bin : 1*® Interface : Parallel® Auto Line Feed : OFF® SLCT-IN Signal Valid® Default Macro : 1®* user can override this setting
Epson LQ-2550 True True DM/C S, P LQ False True I This card provides you with detailed instructions for setting macro 1 using SelecType on your printer for use with PowerPrint. The following settings will be made: 1" skip off, print direction bi-directional, color black, interface parallel, and macro #1 as the default.®®Note: In these instructions we will be giving you step-by-step instructions for defining a SelecType macro. We will be setting macro 1 in order to save any possible changes. By saving these selections to macro 1, the printer will automatically default to them upon power up. These settings can be made to any one of the four (4) macros, however if you decide to save these changes to any macro other than number 1, this macro will have to be loaded when the printer is turned on.®®Note: The ON LINE and left arrow buttons are the same buttons. The FORM FEED and up arrow buttons are the same buttons. The LINE FEED and the down arrow buttons are the same buttons. The LOAD/EJECT and right arrow buttons are the same buttons.®®1. Assuming the printer is on, press the SelecType button. The LCD will display SelecType for two (2) seconds, then display Load Macro.®®2. Press the right arrow button once and ensure the LCD displays LOAD MACRO #1. If the LCD does not display LOAD MACRO #1, press the down arrow button to change this setting.®®3. Press the right arrow button once and the LCD will display MACRO #1 LOADED for two (2) seconds, then displays LOAD MACRO.®®4. Press the down arrow button once and the LCD will display CHANGE MACRO.®®5. Press the right arrow button once and the LCD will display FONT and the current font selection.®®6. Press the up arrow button once and ensure the LCD displays COLOR Black. If the LCD displays Black go to step seven (7). If the LCD does not display Black, press the right arrow button to enter this mode, then either the up arrow or down arrow buttons to change this selection. Once the display reads Black, press the left arrow button to save this setting.®®7. Press the up arrow button once and ensure the LCD displays PRINT DIR. Bi-d. If the LCD displays Bi-d go to step 8. If the LCD does not display Bi-d, press the right arrow button to enter this mode, then either the up arrow or down arrow buttons to change this selection. Once the display reads Bi-d, press the left arrow button to save this setting.®®8. Press the up arrow button six (6) times and ensure the LCD displays 1" SKIP Off. If the LCD displays Off go to step 9. If the LCD does not display Off, press the right arrow button to enter this mode, then either the up arrow or down arrow buttons to change this selection. Once the display reads Off, press the left arrow button to save this setting.®®9. Press the left arrow button once and the LCD will display SAVE MACRO.®®10. Press the right arrow button once to save the newly defined Macro. The LCD will first display MACRO #1 SAVED then CHANGE MACRO.®®11. Press the down arrow button once and ensure the LCD displays CHANGE DEFAULTS.®®12. Press the right arrow button once and ensure the LCD displays INTERFACE Parallel. If the LCD displays Parallel go to step 13. If the LCD does not display Parallel, press the right arrow button to enter this mode, then either the up arrow or down arrow buttons to change this selection. Once the display reads Parallel, press the left arrow button to save this setting.®®13. Press the down arrow button once and ensure the LCD displays AUTO LINE FEED Off. If the LCD displays Off go to step 14. If the LCD does not display Off, press the right arrow button to enter this mode, then either the up arrow or down arrow buttons to change this selection. Once the display reads Off, press the left arrow button to save this setting.®®14. Press the down arrow button once and ensure the LCD displays DC1/DC3 Enable. If the LCD displays Enable go to step 15. If the LCD does not display Enable, press the right arrow button to enter this mode, then either the up arrow or down arrow buttons to change this selection. Once the display reads Enable, press the left arrow button to save this setting.®®15. Press the down arrow button once and ensure the LCD displays DEFAULT MACRO #1. If the LCD displays #1 go to step 16. If the LCD does not display #1, press the right arrow button to enter this mode, then either the up arrow or down arrow buttons to change this selection. Once the display reads #1, press the left arrow button to save this setting.®®16. Press the left arrow button and the LCD will display SAVE DEFAULTS.®®17. Press the right arrow button and the LCD will display DEFAULTS SAVED and then PLEASE TURN OFF. Turn the printer off ®®The printer is now set correctly to work with PowerPrint. You must turn the printer off for a few seconds (about 10 seconds) and then turn it back on again for the changes to take effect.
Epson LX-80 True True DM P, S opt FX False False
Epson LX-86 True True DM P, S opt FX False False
Epson LX-90 True True DM S or P FX False False Parallel interface required.
Epson LX-800 True True DM P, S opt FX False True R Epson@FX-286e
Epson LX-810 True True DM P, S opt FX False True R Epson@FX-286e
Epson SQ-850 True True IJ S, P LQ False True
Epson SQ-2000 True True IJ S or P LQ False False Parallel interface required.
Epson SQ-2500 True True IJ S/DIN-6, P LQ False True
Epson SQ-2550 True True IJ S, P LQ False True
Epson Stylus-300 True False IJ P ESC/P2 False False
Epson Stylus-800 True True IJ P ESC/P2 False False
Epson T-750 True True DM P, S opt FX False True R Epson@FX-286e
Epson T-1000 True True DM P, S opt FX False True R Epson@FX-286e
Esselte Meto LIS-1120 True True L P, S LJ II True False
Esselte Meto LIS-1520 True True L P, S LJ II True False
Facit B1200 True True DM S, P FX False False
Facit B2100 True True DM S, P FX False False
Facit B2150 True True DM S, P FX False False
Facit B2400 True True DM S, P LQ False False
Facit B2450 True True DM S, P LQ False False
Facit B3100 True True DM/C S, P FX False False
Facit B3150 True True DM S, P FX False False
Facit B3150C True True DM/C S, P FX False False
Facit B3350C True True DM/C S, P FX False False
Facit B3450C True True DM/C S, P LQ False False
Facit B3550C True True DM/C S, P FX False False
Facit C7400 True True DM S, P FX False False
Facit C7500 True True DM/C S, P FX False False
Facit D4000 True True DM P, S FX False False
Facit E420 True True DM P, S FX False False
Facit E520 True True DM P, S FX False False
Facit E530 True True DM P, S FX False False
Facit E580 True True DM P, S LQ False False
Facit E590 True True DM P, S LQ False False
Facit E620 True True DM/C P, S FX False False
Facit E630 True True DM/C P, S FX False False
Facit E690 True True DM/C P, S LQ False False
Facit E750 True True DM/C P, S FX False False
Facit E950 True True DM/C S, P FX False False
Facit E7650 True True DM/C S, P FX False False
Facit P5160 True True L P, S opt LJ II False False
Facit P6060 True True L S, P LJ II False False
Facit P7080-A True False L S, P LJ False False
Facit P8100 True True L S, P LJ II False False
Fontex Technology Syslaser True True L S, P LJ II False False
Fortis DM1310 True True DM P, S opt FX False False
Fortis DM2210 True True DM S, P FX False False
Fortis DM2215 True True DM S, P FX False False
Fortis DM3215 True True DM/C S, P FX False False
Fortis DP600S True True L S, P LJ II False False
Fortis DP600W True False L P LJ True False
Fortis DP800 True False L S, P LJ False False
Fortis DQ4110 True True DM S, P LQ False False
Fortis DQ4210 True True DM S, P LQ False False
Fortis DQ4215 True True DM/C S, P LQ False False
Fujitsu Breeze 100 True False IJ P, S opt DJ False False
Fujitsu Breeze 200 True False IJ P, S opt DJ False False
Hewlett Packard LaserJet True False L S or P LJ False True Parallel interface required. D U108185160,11100001 In addition to the dip switch settings shown above, you should verify that the jumper blocks on jumper block JP2 are on connectors 1 and 3.®®You may have to remove a cover plate from the printer to access the dip switches and/or jumper blocks. Refer to your printer manual for more information on these settings.
Hewlett Packard LaserJet II True True L S, P LJ II False True I 1. Turn your printer on and press the ON LINE key once to take the printer off line (ON LINE light should be off).®®2. Press and hold the MENU key for approximately 7 seconds until the LCD display changes and reads SYM SET = ROMAN-8*.®®Note: If you need to make any changes, press the +/- key until the LCD display shows the desired setting, then press the ENTER key to lock the setting. The * will appear when the setting has been locked in.®®3. Press the MENU key once and make sure the display reads AUTO CONT = ON*.®®4. Press the MENU key once and ensure the display reads I/O = PARALLEL*.®®5. Press the MENU key once to display 00 READY.®®6. Press the ON LINE key once to put the printer on-line.®®Your printer is now set to work correctly with PowerPrint.1. Turn your printer on and press the ON LINE key once to take the printer off line (ON LINE light should be off).®®2. Press and hold the MENU key for approximately 7 seconds until the LCD display changes and reads SYM SET = ROMAN-8*.®®Note: If you need to make any changes, press the +/- key until the LCD display shows the desired setting, then press the ENTER key to lock the setting. The * will appear when the setting has been locked in.®®3. Press the MENU key once and make sure the display reads AUTO CONT = ON*.®®4. Press the MENU key once and ensure the display reads I/O = PARALLEL*.®®5. Press the MENU key once to display 00 READY.®®6. Press the ON LINE key once to put the printer on-line.®®Your printer is now set to work correctly with PowerPrint.
Hewlett Packard LaserJet II D True True L S, P LJ II False True I 1. Turn your printer on and press the ON LINE key once to take the printer off line (ON LINE light should be off).®®2. Press and hold the MENU key for approximately 7 seconds until the LCD display changes and reads AUTO CONT = ON*.®®Note: If you need to make any changes, press the +/- key until the LCD display shows the desired setting, then press the ENTER key to lock the setting. The * will appear when the setting has been locked in.®®3. Press the MENU key once and make sure the display reads I/O = PARALLEL*.®®4. Press the MENU key once to display 00 READY.®®5. Press the ON LINE key once to put the printer on-line.®®Your printer is now set to work correctly with PowerPrint.
Hewlett Packard LaserJet II P True True L S, P LJ IIP False True I 1. Turn your printer on and press the ON LINE key once to take the printer off line (ON LINE light should be off).®®2. Press the MENU ten or eleven times until the LCD display changes and reads DEVICE CONFIG.®®Note: If you need to make any changes, press the +/- key until the LCD display shows the desired setting, then press the ENTER key to lock the setting. The * will appear when the setting has been locked in.®®3. Press the ENTER key once and make sure the display reads AUTO CONT = ON*.®®4. Press the MENU key once and ensure the display reads I/O = PARALLEL*.®®5. Press the MENU key once to display 00 READY.®®6. Press the ON LINE key once to put the printer on-line.®®Your printer is now set to work correctly with PowerPrint.
Hewlett Packard LaserJet II P Plus True True L P LJ IIP False False R Hewlett Packard@LaserJet II P
Hewlett Packard LaserJet III True True L S, P LJ III False True I 1. Turn your printer on and press the ON LINE key once to take the printer off line (ON LINE light should be off).®®2. Press and hold the MENU key for approximately 7 seconds until the LCD display changes and reads AUTO CONT = ON*.®®Note: If you need to make any changes, press the +/- key until the LCD display shows the desired setting, then press the ENTER key to lock the setting. The * will appear when the setting has been locked in.®®3. Press the MENU key once and make sure the display reads I/O = PARALLEL*.®®4. Press the MENU key once and make sure the display reads RET = DARK*.®®Note: RET = DARK selects the LaserJet III’s enhanced resolution mode’s highest setting. If you wish to use another setting, please refer to your LaserJet III user’s manual for instructions.®®5. If you have more than the standard one megabyte of memory in your LaserJet III, press the MENU key once and make sure the display reads PAGEPROTECT=OFF*.®®6. Press the MENU key once to display 00 READY.®®7. Press the ON LINE key once to put the printer on-line.®®Your printer is now set to work correctly with PowerPrint.
Hewlett Packard LaserJet III D True True L S, P LJ III False True R Hewlett Packard@LaserJet III
Hewlett Packard LaserJet III P True True L S, P LJ III False True I 1. Turn your printer on and press the ON LINE key once to take the printer off line (ON LINE light should be off).®®2. Press the MENU ten or eleven times until the LCD display changes and reads DEVICE CONFIG.®®Note: If you need to make any changes, press the +/- key until the LCD display shows the desired setting, then press the ENTER key to lock the setting. The * will appear when the setting has been locked in.®®3. Press the ENTER key once and make sure the display reads AUTO CONT = ON*.®®4. Press the MENU key once and ensure the display reads I/O = PARALLEL*.®®5. Press the MENU key once and make sure the display reads RET = DARK*.®®Note: RET = DARK selects the LaserJet III’s enhanced resolution mode’s highest setting. If you wish to use another setting, please refer to your LaserJet III user’s manual for instructions.®®6. If you have more than the standard one megabyte of memory in your LaserJet III, press the MENU key once and make sure the display reads PAGEPROTECT=OFF*.®®7. Press the MENU key once to display 00 READY.®®8. Press the ON LINE key once to put the printer on-line.®®Your printer is now set to work correctly with PowerPrint.
Hewlett Packard LaserJet III Si True True L S, P LJ III False True I 1. Turn your printer on and press the ON LINE key once to take the printer off line (ON LINE light should be off).®®2. Press and hold the MENU key for approximately 7 seconds until the LCD display changes and reads SYS = HP PCL*.®®Note: If you need to make any changes, press the +/- key until the LCD display shows the desired setting, then press the ENTER key to lock the setting. The * will appear when the setting has been locked in.®®3. Press the MENU key once and make sure the display reads SYS SWITCH = ON*.®®4. Press the MENU key once and make sure the display reads AUTO CONT = ON*.®®5. Press the MENU key once and make sure the display reads I/O = PARALLEL*.®®6. Press the MENU key once and make sure the display reads RET = DARK*.®®Note: RET = DARK selects the LaserJet III’s enhanced resolution mode’s highest setting. If you wish to use another setting, please refer to your LaserJet III user’s manual for instructions.®®7. If you have more than the standard one megabyte of memory in your LaserJet III, press the MENU key once and make sure the display reads PAGEPROTECT=OFF*.®®8. Press the MENU key once to display 00 READY.®®9. Press the ON LINE key once to put the printer on-line.®®Your printer is now set to work correctly with PowerPrint.
Hewlett Packard LaserJet Plus True False L S or P LJ False True Parallel interface required. D U108185160,11100001 In addition to the dip switch settings shown above, you should verify that the jumper blocks on jumper block JP2 are on connectors 1 and 3.®You may have to remove a cover plate from the printer to access the dip switches and/or jumper blocks. Refer to your printer manual for more information on these settings.
Hewlett Packard LaserJet 4 True True L P, S LJ IV False True
Hewlett Packard LaserJet 4L True True L P LJ IVL False False
Hewlett Packard LaserJet 4P True False L P, S LJ IV False False
Hewlett Packard LaserJet 4SI True True L P, S LJ IV False True
Hewlett Packard LaserJet 500 True False L S or P LJ False True Parallel interface required.
Hewlett Packard LaserJet 500 Plus True False L S or P LJ False True Parallel interface required.
Hewlett Packard LaserJet 2000 True False L S or P LJ False True Parallel interface required.
Hewlett Packard PaintJet XL300 True True IJ/C S, P LJ III False False Color is not supported.
Hewlett Packard RuggedWriter True True DM S or P LQ False True Parallel interface required.
Hewlett Packard RuggedWriter 480 True True DM S or P LQ False False Parallel interface required.
Honeywell Bull 462 True True DM/C P, S opt FX False False
Honeywell Bull 466 True True DM/C P, S opt FX False False
Hyundai HDP-910 True True DM P, S opt FX False False
Hyundai HDP-920 True True DM P, S opt FX False False
Hyundai HDP-1810 True True DM P, S opt FX False False
Hyundai HDP-1820 True True DM P, S opt FX False False
Hyundai HLP-6000 True True L S, P LJ IIP False False
Impression Technology ZL1 Twin-Ax True True L S, P LJ II False False
JDL AutoPlotter True True DM S, P LQ False True
JDL AutoPlotter XP True True DM/C S, P LQ False False
JDL OmniPlotter True True DM/C S, P LQ False True
JPS MicroSystems MAXX/8 True True L S, P LJ II False False
JRL Systems JR670-1 True True IJ S, P LQ False False
JRL Systems LP300-1 True False L S, P LJ True False
JRL Systems LP300-2 True False L S, P LJ False False
JRL Systems LP301-3 True False L P, S LJ True False
JRL Systems LP301-4 True False L P, S LJ True False
JRL Systems LP330-SS True False L S, P LJ False False
JRL Systems LP340-SS True False L S, P LJ False False
JRL Systems LP400-1 True False L S, P LJ True False
JRL Systems LP401-2 True False L S, P LJ True False
Kentek Info Systems K-2 + True True L S, P LJ II False False
Kentek Info Systems K-3 True True L S, P LJ II False False
Kentek Info Systems K-4 True True L S, P LJ II False False
Kentek Info Systems K-30 True True L S, P LJ II False False
Kentek Info Systems K-30D True True L S, P LJ II False False
Kentek Info Systems K-40D True True L P, S LJ III False False
Kentek Info Systems K-60 True True L P, S LJ III False False
Kodak Diconix 180si True True IJ S or P FX False False Parallel interface required.
Kodak Diconix 300 True True IJ S or P FX False True Parallel interface required. D U208110160Under Cover,0000000008275160,00000000
Kodak Diconix 300W True True IJ S or P FX False True Parallel interface required. D U208110160Under Cover,0000000008275160,00000000
Kodak Diconix 701 True False IJ P DJ False False I The following are detailed instructions for setting the Kodak Diconix 701 printer to work correctly with PowerPrint. Please consult your printer manual if you require more detailed setup instructions than can be provided in this stack.®®Begin with a few sheets of paper loaded in the printer and the printer turned off.®®1. Turn on the power to the printer while holding down the On Line button. Continue to hold the On Line button down for two seconds.®®2. The current printer settings and directions on how to change them will be printed. Verify that the printer settings are set as follows® (1) Emulation = HP DeskJet Plu® (2) Paper Size = US Letter (or US Legal or A4)® (3) Perforation Skip = Off® (4) Orientation = Portrait® (5) Carriage Return = CR® (6) Line Feed = LF® (7) Character Set = PC-8® (8) Text Scale Mode = Off® (9) Gothic Pitch = 16.67 cpi® (10) Receive Buffer Size = 23 Kbytes® (11) Graphic Resolution = 300 dpi®®3. If a setting is set incorrectly, press the ON LINE or LF/FF buttons on the front of the printer to move the printhead to the left or right, respectively. Align the printhead so that the yellow arrows on the printhead are pointing to the number of the setting you wish to change. Press the PRIME button to change the setting which is aligned with the arrows. From the list of options which are printed for the setting, align the arrows with the desired setting using the On LINE and LF/FF buttons and press the PRIME button.®®4. When all of the printer settings are set as the table in step #2 displayed, select Exit (on the far left-hand side) and press the PRIME button. A summary of the new printer settings you selected will be printed with your changes in bold. If the summary matches the settings as listed in step #2 above, select YES when the printer asks if you would like to save your changes.®®Your printer is now set correctly to work with PowerPrint.
Kodak EktaPlus 7008 True False L S, P LJ False False
Kodak EktaPlus 7016 True False L S, P LJ False False
Konica Business Machines LP-3015 True True L S, P LJ II False False
Konica Business Machines LP-3110 True True L S, P LJ II False False
Kyocera F-800 True True L S, P LJ II False True
Kyocera F-800A True True L S, P LJ II False False
Kyocera F-820 True True L P, S LJ II False False
Kyocera F-850 True True L P, S LJ III False False
Kyocera F-1010 True False L S, P LJ False True
Kyocera F-1500A True True L P, S LJ III False False
Kyocera F-1800A True True L S, P LJ II False True
Kyocera F-2000A True True L S, P LJ II False True
Kyocera F-2010 True True L S, P LJ II False True
Kyocera F-3000A True True L S, P LJ II False True
Kyocera F-3010 True True L S, P LJ II False True
Kyocera F-3500A True True L P, S LJ III False False
Kyocera F-5000A True True L S, P LJ III False False
Kyocera F-5500A True True L P, S LJ III False False
Kyocera FS-1500A True True L S, P LJ III False False
Lee Data 1314W True True DM P FX False False
Lee Data 1315 True True DM P FX False False
Mannesmann Tally MT 150/9 True True DM P, S opt FX False False
Mannesmann Tally MT 340 True True DM/C P, S opt FX False False
Mannesmann Tally MT 490 True True DM S or P FX False False Parallel interface required.
Mannesmann Tally MT 645 True True DM S, P FX False False
Mannesmann Tally MT 661 True True DM S, P FX False False
Mannesmann Tally MT 691 True True DM P, S FX False False
Mannesmann Tally MT 735 True True TT P LJ II False True
Mannesmann Tally MT 904 True True L S, P LJ IIP False False
Mannesmann Tally MT 905 True True L S, P LJ II False True
Mannesmann Tally MT 906 True True L S, P LJ II False False
Mannesmann Tally MT 906WP True True L S, P LJ II False False
Mannesmann Tally MT 908 True True L S, P LJ III False False
Mannesmann Tally MT 910 True False L S, P LJ False True
Mannesmann Tally MT 911 True True L S, P LJ II False False
Mannesmann Tally MT 911PS True True L S, P LJ II False False
Mannesmann Tally MT 7400C True False TT S or P DJ False False Color is not supported. Parallel interface required.
Memorex 1208 True True DM/C P, S opt FX False False
Memorex 1815-1 True False L S, P LJ False False
Memorex 1815-2 True False L S, P LJ False False
Memorex 2018 True False L S, P LJ False False
Memorex 2108-A True False L S or P LJ False False Parallel interface required.
Memorex 2108-B True False L S or P LJ False False Parallel interface required.
Memorex 2115 True False L P LJ False False
Miltope Business Series 30L True True L P LJ II False False
Miltope Business Series 30M True True L P LJ II True False
Minolta SP10CL True True L S, P LJ III False False
Minolta SP101 True True L S, P LJ II False False
Minolta SP130 True False L S, P LJ False False
Minolta SP-6CL True True L P, S LJ III False False
Minolta SP-6DL True True L P, S LJ III False False
Mita Copystar LP-2080 True True L S, P LJ II False False
Mita Copystar LP-2085 True True L S, P LJ III False False
Mita Copystar LP-3155 True True L S, P LJ II False False
Mita Copystar LP-3160 True True L S, P LJ III False False
Mitek Systems 120T True False L S, P LJ False False
Mitek Systems 125T True False L S, P LJ False False
Mitek Systems 150T True False L S, P LJ False False
Mitek Systems 2150 True False L S, P LJ False False
NCR 577 True True DM/C P, S FX False False
NCR 6417 True True DM P, S opt FX False False
NCR 6421 True True DM S or P FX False False Parallel interface required.
NCR 6424 True True DM S, P FX False False
NCR 6435 True True L S, P LJ II False False
NCR 6436-0201 True False L S, P LJ False False
NCR 6436-0301 True True L P LJ II False False
NCR 6436-0501 True True L S, P LJ II False False
NEC JetMate True False IJ P, S opt DJ5C False False
NEC P5XL True True DM/C P, S opt NEC-PW False True D D308050160SW 1,1111111108185160SW2,1111111108320160SW3,11111101
NEC P6 True True DM P, S opt NEC-PW False True D U208100160SW1,0000000008275160SW2,00000010
NEC P7 True True DM P, S opt NEC-PW False True D U208100160SW1,0000000008275160SW2,00000010
NEC P9 True True DM P, S opt NEC-PW False True
NEC P20 True True DM P, S opt NEC-PW False False
NEC P30 True True DM P, S opt NEC-PW False False
NEC P60 True True DM/C P, S opt NEC-PW False False
NEC P70 True True DM/C P, S opt NEC-PW False False
NEC P90 True True DM/C P, S opt NEC-PW False False
NEC P2200 True True DM P, S opt NEC-PW False True I The following settings will be made: form feed length 11 inches, skip over perforation off, 6 lines per inch, auto line feed off, auto carriage return on, buffer full auto line feed off, sheet feeder, and parallel interface.®®Note: The QUIT and QUIET buttons are the same buttons. The NO and PRINT STYLE buttons are the same buttons. The YES and FEED buttons are the same buttons. The ENTER and SELECT buttons are the same buttons.®®Note: Press the YES button to move to the next selection. Press the NO button to choose mode in main menu or to change a setting in a mode. Press the QUIT button to exit or save®®Note: The bracket around the selection is the current selection.®®1. Press and hold the SELECT button while turning on the printer. This will cause the printer to print the Printer Memory Settings.®®2. Press the NO button twice to enter the Form Settings menu.®®3. Press the YES button once and ensure the Forms Settings menu, Form Feed Length In Inches selection is 11 inches. If the current setting is not 11 inches, press the NO button to change this setting.®®4. Press the YES button once and ensure the Forms Setting menu, Skip Over Perforation selection is OFF. If the current setting is not OFF, press the NO button to change this setting.®®5. Press the YES button once and ensure the Forms Setting menu, Line Per Inch selection is 6. If the current setting is not 6, press the NO button to change this setting.®®6. Press the YES button once and ensure the Forms Setting menu, Auto Line Feed selection is OFF. If the current setting is not OFF, press the NO button to change this setting.®®7. Press the YES button once and ensure the Forms Setting menu, Auto Carriage Return selection is ON. If the current setting is not ON, press the NO button to change this setting.®®8. Press the YES button once and ensure the Forms Setting menu, Buffer Full Auto Line Feed selection is OFF. If the current setting is not OFF, press the NO button to change this setting.®®9. Press the YES button once and ensure the Forms Setting menu, Sheet Feeder selection is NOT INSTALLED. If you have a sheet feeder installed make sure this selection is INSTALLED. If the current setting is not correct, press the NO button to change this setting.®®10. Press the QUIT button once to enter the Interface Settings menu.®®11. Press the YES button once and ensure the Interface Settings menu, Mode selection is Parallel. If the current setting is not Parallel, press the NO button to change this setting.®®12. Press the QUIT button two (2) times to save your Printer Memory Settings.®®13. Press the YES button once to exit to ON-LINE status.®®The printer is now set correctly to work with PowerPrint.
NEC P2200XE True True DM/C P, S opt NEC-PW False True
NEC P3200 True True DM P, S opt NEC-PW False False
NEC P3300 True True DM P, S opt NEC-PW False False
NEC P5200 True True DM P, S opt NEC-PW False True
NEC P5300 True True DM P, S opt NEC-PW False True
NEC P6200 True True DM/C P NEC-PW False True
NEC P6300 True True DM/C P, S opt NEC-PW False True
NEC P8300 True True DM P, S opt NEC-PW False True
NEC P9300 True True DM/C P, S opt NEC-PW False False
NEC Silentwriter LC 260 True True L S, P LJ II False True
NEC Silentwriter LC 860 True True L S, P LJ II False True
NEC SuperScript 610 True True L P LJ IIP False False
Newbury Data OSP 3 True True DM/C S or P FX False False Parallel interface required.
Nissho NP 2405 True True DM S, P LQ False True
Nissho NP 2410 True True DM S, P LQ False True
North Atlantic Ind. 8-PS 800+ True False L S, P opt LJ False False Parallel interface required.
North Atlantic Ind. Smartwriter 80 True False L S, P LJ False False
Octus LaserPro 90/22 Plus True True L S, P LJ II False False
Octus LaserPro 90/24E True True L S, P LJ II False False
Octus LaserPro 1510 MICR True False L S, P LJ False False
Octus LaserPro 1510 Plus True False L P, S LJ False False
Octus LaserPro 2200 True False L P or S LJ False False Parallel interface required.
Office Automation LaserPro 90/22 True True L S, P LJ II False False
Office Automation LaserPro 90/8 True True L S, P LJ II False False
Office Automation LaserPro 810-R True False L S, P LJ False False
Office Automation LaserPro 1510 True False L S or P LJ False False Parallel interface required.
Office Automation LaserPro 2200 True False L S or P LJ False False Parallel interface required.
Office Automation LaserPro Exec True True L S, P LJ II False False
Office Automation LaserPro Express Series II True False L S, P LJ False False
Office Automation LaserPro Gold Express True False L S, P LJ False False
Office Automation LaserPro Silver Express True False L S, P LJ False False
Okidata DOC•IT 3000 True True L P, S LJ II False False
Okidata DOC•IT 4000 True True L P, S LJ II False False
Okidata LaserLine 6 True True L P, S opt LJ II False True
Okidata MicroLine 520 True True DM P, S opt FX False False
Okidata MicroLine 520 True True DM/C P FX False False
Okidata MicroLine 521 True True DM P, S opt FX False False
Okidata MicroLine 521 True True DM/C P FX False False
Okidata MicroLine 184 Turbo True True DM P, S opt FX False False Some models do not have Epson FX emulation and so will not work with PowerPrint.
Okidata MicroLine 280 True True DM P, S opt FX False False
Okidata MicroLine 320 True True DM P, S opt FX False True Some models do not have Epson FX emulation and so will not work with PowerPrint. I The following settings will be made: Epson emulation, bi-directional printing on, LPI 6, skip over perforation off, auto LF off, and auto CR off.®®Turn your printer on to confirm or set your control panel settings.®®Note: The ITEM setting printed is the current setting ®®Note: Press the GROUP, ITEM and SET buttons to move to the next GROUP, ITEM OR SETing, respectively. The current setting for an Item is the last one printed. To make the setting current, simply press the SET button until the setting is printed. You may have to press the SET button more than once to obtain the recommended setting. If you lose track at any time while setting the Control Panel, press the GROUP and ITEM buttons to go back to the menu of a previous level.®®Note: The GROUP and the LINE FEED buttons are the same buttons. The ITEM and FORM FEED buttons are the same buttons. The SET and the TOF/QUIET buttons are the same buttons.®®1. Press the SEL button once to take the printer off line.®®2. Press the MODE button once put the printer in Menu Select mode.®®3. Press the GROUP button once and the Font Group’s current setting for the item will print.®®4. Press the GROUP button and ensure the General Control Group, Emulation Mode item setting is Epson FXe. If the current setting is not Epson FXe, press the SET button to change this setting.®®5. Press the ITEM button once and ensure the General Control Group, Graphics Item setting is Bi-directional. If the current setting is not Bi-directional, press the SET button to change this setting.®®6. Press the GROUP button once and ensure the Vertical Control Group, Line Spacing Item setting is 6 LPI. If the current setting is not 6 LPI, press the SET button to change this setting.®®7. Press the ITEM button twice and ensure the Vertical Control Group, Skip Over Perforation item setting is No. If the current setting is not NO, press the SET button to change this setting.®®8. Press the ITEM button once and ensure the Vertical Control Group, Auto LF Item setting is NO. If the current setting is not NO, press the SET button to change this setting.®®9. Press the ITEM button once and ensure the Vertical Control Group, Auto CR Item setting is NO. If the current setting is not NO, press the SET button to change this setting.®®10. Press the MODE button and the printer will go back on line.®®The printer is now set correctly to work with PowerPrint.
Okidata MicroLine 320 Elite True True DM P, S opt FX False False Some models do not have Epson FX emulation and so will not work with PowerPrint. R Okidata@MicroLine 320
Okidata MicroLine 321 True True DM P, S opt FX False True R Okidata@MicroLine 320
Okidata MicroLine 321 Elite True True DM P, S opt FX False False R Okidata@MicroLine 320
Okidata MicroLine 380 True True DM P, S opt LQ False True I The following settings will be made: cut sheet feeder, bi-directional printing on, parallel interface, 6 LPI, skip over perforation off, and auto LF off.®®Turn your printer on to confirm or set your control panel settings.®®Note: The ITEM setting printed is the current setting ®®Note: Press the GROUP, ITEM and SET buttons to move to the next GROUP, ITEM OR SETing, respectively. The current setting for an Item is the last one printed. To make the setting current, simply press the SET button until the setting is printed. You may have to press the SET button more than once to obtain the recommended setting. If you lose track at any time while setting the Control Panel, press the GROUP and ITEM buttons to go back to the menu of a previous level.®®Note: The GROUP and the FEED buttons are the same buttons. The ITEM and TOF/PARK buttons are the same buttons. The SET and the FONT buttons are the same buttons. The PRINT and the PITCH buttons are the same buttons.®®1. Press the SELECT button once to take the printer off line.®®2. Press the SET and PRINT buttons simultaneously to enter the Menu mode.®®3. Press the GROUP button once and the Font Group’s current setting for the item will print.®®4. Press the GROUP button and ensure the General Control Group, Cut Sheet Feeder Item setting is Not Installed. If you are using the cut sheet feeder 3800 (CSF-3800), configure the Cut Sheet Feeder Item setting for Installed. If the current setting is not the correct one, press the SET button to change this setting.®®5. Press the ITEM button once and ensure the General Control Group, Graphics Item setting is Bi-directional. If the current setting is not Bi-directional, press the SET button to change this setting.®®6. Press the ITEM button four (4) times and ensure the General Control Group, Interface Item setting is Parallel. If the current setting is not Parallel, press the SET button to change this setting.®®7. Press the GROUP button once and ensure the Vertical Control Group, Line Spacing Item setting is 6 LPI. If the current setting is not 6 LPI, press the SET button to change this setting.®®8. Press the ITEM button twice and ensure the Vertical Control Group, Skip Over Perforation item setting is NO. If the current setting is not NO, press the SET button to change this setting.®®9. Press the ITEM button once and ensure the Vertical Control Group, Auto LF Item setting is NO. If the current setting is not NO, press the SET button to change this setting.®®10. Press the SELECT button and the printer will go back on line.®®The printer is now set correctly to work with PowerPrint
Okidata MicroLine 390 True True DM P, S opt LQ False True R Okidata@MicroLine 380
Okidata MicroLine 390 Elite True True DM S, P LQ False False R Okidata@MicroLine 380
Okidata MicroLine 390 FB True True DM P, S opt LQ False False R Okidata@MicroLine 380
Okidata MicroLine 390 Plus True True DM P, S opt LQ False False R Okidata@MicroLine 380
Okidata MicroLine 391 True True DM P, S opt LQ False True I The following settings will be made: Epson LQ emulation, bi-directional printing on, 6 LPI, skip over perforation off, auto LF off, and auto CR off.®®Turn your printer on to confirm or set your control panel settings.®®Note: The ITEM setting printed is the current setting ®®Note: Press the GROUP, ITEM and SET buttons to move to the next GROUP, ITEM OR SETing, respectively. The current setting for an Item is the last one printed. To make the setting current, simply press the SET button until the setting is printed. You may have to press the SET button more than once to obtain the recommended setting. If you lose track at any time while setting the Control Panel, press the GROUP and ITEM buttons to go back to the menu of a previous level.®®Note: The GROUP and the LINE FEED buttons are the same buttons. The ITEM and FORM FEED buttons are the same buttons. The SET and the PARK buttons are the same buttons.®®1. Press the SEL button once to take the printer off line.®®2. Press the MODE button once put the printer in Menu Select mode.®®3. Press the GROUP button once and the Font Group’s current setting for the item will print.®®4. Press the GROUP button and ensure the General Control Group, Emulation Mode item setting is Epson LQ. If the current setting is not Epson LQ, press the SET button to change this setting.®®5. Press the ITEM button once and ensure the General Control Group, Graphics Item setting is Bi-directional. If the current setting is not Bi-directional, press the SET button to change this setting.®®6. Press the GROUP button once and ensure the Vertical Control Group, Line Spacing Item setting is 6 LPI. If the current setting is not 6 LPI, press the SET button to change this setting.®®7. Press the ITEM button twice and ensure the Vertical Control Group, Skip Over Perforation item setting is No. If the current setting is not NO, press the SET button to change this setting.®®8. Press the ITEM button once and ensure the Vertical Control Group, Auto LF Item setting is NO. If the current setting is not NO, press the SET button to change this setting.®®9. Press the ITEM button once and ensure the Vertical Control Group, Auto CR Item setting is NO. If the current setting is not NO, press the SET button to change this setting.®®10. Press the MODE button and the printer will go back on line.®®The printer is now set correctly to work with PowerPrint.
Okidata MicroLine 391 Elite True True DM S, P LQ False False R Okidata@MicroLine 391
Okidata MicroLine 391 Plus True True DM P, S opt LQ False False R Okidata@MicroLine 391
Okidata MicroLine 393 True True DM S, P LQ False True I The following settings will be made: 6 lines per inch, bi-directional printing on, DC1/DC3 active, skip over perforation off, auto LF off, and Epson character set.®®Turn your printer on to confirm or set your Control Panel settings.®®Note: The first setting printed is the current setting.®®Note: To move back to the previous menu item, press LINE FEED. To move on to the next menu item, press FORM FEED. To set a selection and move to the next menu item, press FORM FEED. (The instructions to set a selection are included in these steps.) To exit menu mode, press TOP OF FORM. To change the selection for a menu item, press SELECT.®®Note: If you lose track at any time while setting the Control Panel, press the LINE FEED button to go back to the previous Menu Selection.®®1. Assuming the printer is turned on and the SELECT light is lit, hold the PRINT QUALITY button in and then press the FONT SELECT button. The Okidata Microline 393 will print MENU PRINT?®®2. Press the FORM FEED button once and ensure the Menu Selection, LPI is 6. If the current setting is not LPI 6, press the SELECT button to change this setting.®®3. Press the FORM FEED button eight (8) times and ensure the Menu Selection, Graphics Printing is Bidirectional. If the current setting is not Bidirectional press the SELECT button to change this setting®®4. Press the FORM FEED button three (3) times and ensure the Menu Selection, DC1/DC3 Active is Yes. If the current setting is not Yes press the SELECT button to change this setting.®®5. Press the FORM FEED button once and ensure the Menu Selection, Skip Over Perforation is NO. If the current setting is not NO press the SELECT button to change this setting.®®6. Press the FORM FEED button once and ensure the Menu Selection, Auto LF is NO. If the current setting is not NO press the SELECT button to change this setting.®®7. Press the FORM FEED button four (4) times and ensure the Menu Selection, Character Set setting is Epson. If the current setting is not Epson press the SELECT button to change this setting.®®8. Press the TOP OF FORM button and the printer will go back, on line.®®The printer is now set correctly to work with PowerPrint.
Okidata MicroLine 393 B Plus True True DM P, S LQ False False
Okidata MicroLine 393 C True True DM/C S, P LQ False True I The following settings will be made: 6 lines per inch, bi-directional printing on, DC1/DC3 active, ribbon selection, skip over perforation off, auto LF off, and Epson character set.®®Turn your printer on to confirm or set your Control Panel settings.®®Note: The first setting printed is the current setting ®®Note: To move back to the previous menu item, press LINE FEED. To move on to the next menu item, press FORM FEED. To set a selection and move to the next menu item, press FORM FEED. (The instructions to set a selection are included in these steps.) To exit menu mode, press TOP OF FORM. To change the selection for a menu item, press SELECT.®®Note: If you lose track at any time while setting the Control Panel, press the LINE FEED button to go back to the previous Menu Selection.®®1. Assuming the printer is turned on and the SELECT light is lit, hold the PRINT QUALITY button in and then press the FONT SELECT button. The Okidata Microline 393C will print MENU PRINT?®®2. Press the FORM FEED button once and ensure the Menu Selection, LPI is 6. If the current setting is not LPI 6, press the SELECT button to change this setting.®®3. Press the FORM FEED button eight (8) times and ensure the Menu Selection, Graphics Printing is Bidirectional. If the current setting is not Bidirectional press the SELECT button to change this setting.®®4. Press the FORM FEED button two (2) times and ensure the Menu Selection, Color is Black Ribbon. If you are using a color ribbon ensure the Menu Selection Color is Black. If the current setting is not the correct one press the SELECT button to change this setting.®®5. Press the FORM FEED button two (2) times and ensure the Menu Selection, DC1/DC3 Active is Yes. If the current setting is not Yes press the SELECT button to change this setting.®®6. Press the FORM FEED button once and ensure the Menu Selection, Skip Over Perforation is NO. If the current setting is not NO press the SELECT button to change this setting.®®7. Press the FORM FEED button once and ensure the Menu Selection, Auto LF is NO. If the current setting is not NO press the SELECT button to change this setting.®®8. Press the FORM FEED button four (4) times and ensure the Menu Selection, Character Set setting is Epson. If the current setting is not Epson press the SELECT button to change this setting.®®9. Press the TOP OF FORM button and the printer will go back, on line.®®The printer is now set correctly to work with PowerPrint.
Okidata MicroLine 393 C Elite True True DM/C S, P LQ False False R Okidata@MicroLine 393 C
Okidata MicroLine 393 C Plus True True DM/C P, S LQ False False
Okidata MicroLine 393 Elite True True DM S, P LQ False False R Okidata@MicroLine 393
Okidata MicroLine 393 Plus True True DM/C S, P LQ False False R Okidata@MicroLine 393
Okidata MicroLine 520 True True DM P, S opt FX False False
Okidata MicroLine 521 True True DM P, S opt FX False False
Panasonic KX-P1124 True True DM P, S opt LQ False True I The following settings will be made: Epson italic printer emulation mode, cut sheet feeder mode, data length mode, print width mode, print direction mode, skip perforation mode, automatic line feed mode, and automatic carriage return mode.®®Note: If the instructions and terminology are not detailed enough, we strongly urge you to consult “Setting the Initial Setup mode” instructions beginning on page 3-12 in the Panasonic KX-P1124 manual. The diagram on page 3-15 is particularly helpful.®®Note: The COLUMN and the QUIET switches are the same switches. The SET and P.CUT switches are the same switches.®®Note: If you loose track any time while using the Control Table, press the ROW button until you return to the previous instructions.®®1. Turn the printer on while pressing the FUNCTION switch to enter the Initial Setup mode. The ON LINE indicator light should be blinking.®®2. Ensure the indicator lights are ON for C1 and OFF for C2, C3, C4, C5, and C6. If the indicator light is not lit press the COLUMN switch to change this setting. Once C1 is lit, press the SET switch to save this setting.®®Note: In the ROW indicator condition: ON=light is lit, BLK=light is blinking, OFF=light is out.®®Note: When changing a column setting (using the column switch to change a setting) the Initial Setup mode, a lit indicator light means setting is ON, while a blinking indicator light is OFF. See page 3-14, number 2 in the KX-P1124 manual.®®3. Press the ROW switch four (4) times and ensure the indicator lights are OFF for C1, ON for C2, OFF for C3, OFF for C4, and OFF for C5. C6 doesn’t matter. If the indicator lights are not set correctly use the COLUMN switch to change these settings. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®4. Press the ROW switch two (2) times and ensure the indicator lights are OFF for C1, OFF for C2, OFF for C5 and OFF for C6. C3 and C4 do not matter. If the KX-P36 cut sheet feeder is installed, the indicator light should be ON for C2. If the indicator lights are not set correctly use the COLUMN switch to change these settings. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®5. Press the FUNCTION button and the printer will go back on line.®®The printer is now set correctly to work with PowerPrint.
Panasonic KX-P1180 True True DM P, S opt FX False True D U108185160,00000000
Panasonic KX-P1180i True True DM P, S opt FX False False
Panasonic KX-P1191 True True DM P, S opt FX False False D U108185160,00000000
Panasonic KX-P1524 True True DM S, P LQ False True
Panasonic KX-P1592 True True DM P, S opt FX False True D U208100160SW1,1100111008275160SW2,11001000 When using a sheet feeder dip switch 6 on SW2 should be in the up position (on).
Panasonic KX-P1595 True True DM P, S opt FX False True
Panasonic KX-P1624 True True DM P, S opt LQ False True I The following settings will be made: Epson italic printer emulation mode, cut sheet feeder mode, data length mode, print width mode, print direction mode, skip perforation mode, automatic line feed mode, and automatic carriage return mode.®®Note: If the instructions and terminology are not detailed enough, we strongly urge you to consult “Setting the Initial Setup mode” instructions beginning on page 3-15 in the Panasonic KX-P1624 manual. The diagram on page 3-18 is particularly helpful.®®Note: The COLUMN and the QUIET switches are the same switches. The SET and P.CUT switches are the same switches.®®Note: If you loose track any time while using the Control Table, press the ROW button until you return to the previous instructions.®®Note: If you are a brave person and do not care about your current Control Table settings or Macros, a very fast way to set the Initial Setup mode is to reset all settings to the FACTORY DEFAULT. The accomplish this:®®1. Turn the printer on while pressing the FUNCTION switch to enter the Initial Setup mode. The ON LINE indicator light should be blinking.®®2. Press the FF switch®®3. Press the SET switch®®4. Press the FUNCTION switch to release the Initial Setup mode.®®The Panasonic KX-P1624 printer is now set correctly to work with PowerPrint.®®If you are not that brave (we don’t blame you) follow these instructions step by step to set the Initial Setup mode:®®1. Turn the printer on while pressing the FUNCTION switch to enter the Initial Setup mode. The ON LINE indicator light should be blinking.®®2. Press the ROW switch once and ensure the indicator light on C1 is lit. If the indicator light is not lit press the COLUMN switch to change this setting. Once C1 is lit, press the SET switch to save this setting.®®Note: In the ROW indicator condition: ON=light is lit, BLK=light is blinking, OFF=light is out.®®Note: When changing a column setting (using the column switch to change a setting) the Initial Setup mode, a lit indicator light means setting is ON, while a blinking indicator light is OFF. See page 3-14, number 2 in the KX-P1624 manual.®®3. Press the ROW switch six (6) times and ensure the lights are OFF for C1, OFF for C2, OFF for C5 and OFF for C6. C3 and C4 do not matter. If the KX-P38 cut sheet feeder is installed, the indicator light should be ON for C2. If the indicator lights are not set correctly use the COLUMN switch to change these settings. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®4. Press the ROW switch once and ensure the lights are OFF for C1, ON for C2, OFF for C3, OFF for C4, and OFF for C5. C6 doesn’t matter. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®5. Press the FUNCTION button and the printer will go back on line.®®The printer is now set correctly to work with PowerPrint.
Panasonic KX-P1654 True True DM S, P LQ False False
Panasonic KX-P1695 True True DM P, S opt FX False True I The following settings will be made: Epson italic printer emulation mode, cut sheet feeder mode, data length mode, print width mode, print direction mode, skip perforation mode, automatic line feed mode, and automatic carriage return mode.®®Note: If the instructions and terminology are not detailed enough, we strongly urge you to consult “Setting the Initial Setup mode” instructions beginning on page 3-15 in the Panasonic KX-P1695 manual. The diagram on page 3-18 is particularly helpful.®®Note: The COLUMN and the QUIET switches are the same switches. The SET and P.CUT switches are the same switches.®®Note: If you loose track any time while using the Control Table, press the ROW button until you return to the previous instructions.®®Note: If you are a brave person and do not care about your current Control Table settings or Macros, a very fast way to set the Initial Setup mode is to reset all settings to the FACTORY DEFAULT. The accomplish this:®®1. Turn the printer on while pressing the FUNCTION switch to enter the Initial Setup mode. The ON LINE indicator light should be blinking.®®2. Press the FF switch®®3. Press the SET switch®®4. Press the FUNCTION switch to release the Initial Setup mode.®®The printer is now set correctly to work with PowerPrint.®®If you are not that brave (we don’t blame you) follow these instructions step by step to set the Initial Setup mode:®®1. Turn the printer on while pressing the FUNCTION switch to enter the Initial Setup mode. The ON LINE indicator light should be blinking.®®2. Press the ROW switch once and ensure the indicator light on C1 is lit. If the indicator light is not lit press the COLUMN switch to change this setting. Once C1 is lit, press the SET switch to save this setting.®®Note: In the ROW indicator condition: ON=light is lit, BLK=light is blinking, OFF=light is out.®®Note: When changing a column setting (using the column switch to change a setting) the Initial Setup mode, a lit indicator light means setting is ON, while a blinking indicator light is OFF. See page 3-14, number 2 in the KX-P1624 manual.®®3. Press the ROW switch six (6) times and ensure the lights are OFF for C1, OFF for C2, OFF for C5 and OFF for C6. C3 and C4 do not matter. If the KX-P38 cut sheet feeder is installed, the indicator light should be ON for C2. If the indicator lights are not set correctly use the COLUMN switch to change these settings. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®4. Press the ROW switch once and ensure the lights are OFF for C1, ON for C2, OFF for C3, OFF for C4, and OFF for C5. C6 doesn’t matter. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®5. Press the FUNCTION button and the printer will go back on line.®®The printer is now set correctly to work with PowerPrint.
Panasonic KX-P4400 Sidewriter True True L P LJ IIP False False
Panasonic KX-P4410 True True L P LJ II False False
Panasonic KX-P4420 True True L P, S opt LJ II False True
Panasonic KX-P4430 True True L S, P LJ III False False
Panasonic KX-P4440 True True L P, S LJ III False False
Panasonic KX-P4450i True True L S, P LJ II False True
Panasonic KX-P4451 True True L P, S LJ III False False
Panasonic KX-P5400 Sidewriter True True L P LJ II False False
PCPI 1000 True False L S, P LJ False False
PCPI 1030 True True L S, P LJ II False False
PCPI 1030-ID True True L S, P LJ II False False
PCPI 1030-IS True True L S, P LJ II False False
PCPI 1030-LN03+ True True L S, P LJ II False False
PCPI 1030-PP True True L S, P LJ II False False
PCPI 1032 True True L S, P LJ II False False
PCPI 1034 True True L S, P LJ II False False
PCPI 1035 True True L S, P LJ II False False
PCPI 1100-PS True True L S, P LJ II False False
PCPI 2000 True False L S, P LJ False False
PCPI 2020 True True L S, P LJ II False False
PCPI 2020-ID True True L S, P LJ II False False
PCPI 2020-IS True True L S, P LJ II False False
PCPI 2020-PP True False L S, P LJ False False
PCPI 2022 True False L S, P LJ False False
PCPI 2024 True True L S, P LJ II False False
PCPI 2025 True True L S, P LJ II False False
PCPI 2500-ID True True L S, P LJ II False False
PCPI 2500-IS True True L S, P LJ II False False
PCPI 2500-OA True True L S, P LJ II False False
PCPI 2500-PP True True L S, P LJ II False False
PCPI 3000 True False L S, P LJ False False
PCPI 3020 True True L S, P LJ II False False
PCPI 3020-ID True True L S, P LJ II False False
PCPI 3020-IS True True L S, P LJ II False False
PCPI 3020-LN03+ True True L S, P LJ II False False
PCPI 3020-PP True True L S, P LJ II False False
PCPI 3022 True True L S, P LJ II False False
PCPI 3024 True True L S, P LJ II False False
PCPI 3025 True True L S, P LJ II False False
Pentax Technologies Laserfold 240 True True L S, P FX False False
Prime Computer 3450 True False L S, P LJ False False
Prime Computer 3451 True True L S, P LJ II False False
Printek 930 DLX True True DM S, P FX False False
Printek FormsPro 2000 True True DM S, P FX False False
Printek FormsPro 4000 True True DM S, P FX False False
Printer Systems IntelliPrint 106 True True L S, P LJ II False False
Printer Systems IntelliPrint 218 True True L S, P LJ II False False
Printronix 2324 Net LANPrinter True True L S, P LJ II False False
Printronix L1012 True False L S or P LJ False False Parallel interface required.
Printronix L2324-D Net LANPrinter True True L P, S LJ II False False
Printronix L2324-D PagePrinter True True L S, P LJ II False False
Printronix L2324-S Net LANPrinter True True L P, S LJ II False False
Printronix L2324-S PagePrinter True True L S, P LJ II False False
Printronix L2624 True True L S, P LJ II True False
Printronix L3824-D PagePrinter True True L S, P LJ II True False
Printronix P1013 True True DM P LQ False False
Printronix P3240 True True DM S, P LQ False False
PrintWare 720 IQ/1200HD True False L S, P LJ False False
Q/COR QuadLaser I True False L S or P LJ False False Parallel interface required.
QMS 2308/S Turbo ImageServer XP True False L P opt LJ False False
QMS 3308/S Turbo ImageServer XP True False L P opt LJ False False
QMS 3320 Turbo ImageServer XP True False L P opt LJ False False
QMS 5320 Turbo ImageServer XP True False L P opt LJ False False
QMS 6320 Turbo ImageServer XP True False L P opt LJ False False
QMS 7320 Turbo ImageServer XP True False L P opt LJ False False
QMS Big Kiss True False L P, S opt LJ False False
QMS ImageStation/S True True L P FX False False
QMS Kiss Plus True False L S, P LJ True False
QMS PS 800 II True False L S, P LJ False False
QMS SmartWriter 80 + True False L S, P LJ False False
Quadram QuadLaser + True False L S, P LJ False False
Quadram QuadLaser I True False L S or p LJ False False Parallel interface required.
Qume CrystalPrint Series II True True L S, P LJ II False False
Qume CrystalPrint Super Series II True True L S, P LJ II False False
Qume CrystalPrint WP True False L P LJ True False
Qume LaserTen True False L S, P LJ False False
Raster Devices RD2 True False L LJ False False
Relisys RP 1814 True True DM P, S opt FX False False
Relisys RP 2410 True True DM P, S opt FX False False
Ricoh Laser 6000 True False L S, P LJ False False
Roland LP-800 True True L P, S opt LJ II False False
Roland PR-1212A True True DM P, S opt FX False False
Roland PR-1515 True True DM S or P LQ False False Parallel interface required.
Roland PR-2416 True True DM P, S opt LQ False True
Roland PR-2417 True True DM P, S opt LQ False True I The following settings will be made: Epson italic printer emulation mode, cut sheet feeder mode, data length mode, print width mode, print direction mode, skip perforation mode, automatic line feed mode, and automatic carriage return mode.®®Note: If the instructions and terminology are not detailed enough, we strongly urge you to consult “Setting the Initial Setup mode” instructions beginning on page 3-12 in the Roland Raven PR-2417 manual. The diagram on page 3-15 is particularly helpful.®®Note: The COLUMN and the QUIET switches are the same switches. The SET and P.CUT switches are the same switches.®®Note: If you loose track any time while using the Control Table, press the ROW button until you return to the previous instructions.®®1. Turn the printer on while pressing the FUNCTION switch to enter the Initial Setup mode. The ON LINE indicator light should be blinking.®®2. Ensure the indicator lights are ON for C1 and OFF for C2, C3, C4, C5, and C6. If the indicator light is not lit press the COLUMN switch to change this setting. Once C1 is lit, press the SET switch to save this setting.®®Note: In the ROW indicator condition: ON=light is lit, BLK=light is blinking, OFF=light is out.®®Note: When changing a column setting (using the column switch to change a setting) the Initial Setup mode, a lit indicator light means setting is ON, while a blinking indicator light is OFF. See page 3-14, number 2 in the PR-2417 manual.®®3. Press the ROW switch four (4) times and ensure the indicator lights are OFF for C1, ON for C2, OFF for C3, OFF for C4, and OFF for C5. C6 doesn’t matter. If the indicator lights are not set correctly use the COLUMN switch to change these settings. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®4. Press the ROW switch two (2) times and ensure the indicator lights are OFF for C1, OFF for C2, OFF for C5 and OFF for C6. C3 and C4 do not matter. If the KX-P36 cut sheet feeder is installed, the indicator light should be ON for C2. If the indicator lights are not set correctly use the COLUMN switch to change these settings. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®5. Press the FUNCTION button and the printer will go back on line.®®The printer is now set correctly to work with PowerPrint.
Roland PR-2418 True True DM P LQ False False
Roland PR-2465 True True DM P, S opt LQ False True I The following settings will be made: Epson italic printer emulation mode, cut sheet feeder mode, data length mode, print width mode, print direction mode, skip perforation mode, automatic line feed mode, and automatic carriage return mode.®®Note: If the instructions and terminology are not detailed enough, we strongly urge you to consult “Setting the Initial Setup mode” instructions beginning on page 3-15 in the printer manual. The diagram on page 3-18 is particularly helpful.®®Note: The COLUMN and the QUIET switches are the same switches. The SET and P.CUT switches are the same switches.®®Note: If you loose track any time while using the Control Table, press the ROW button until you return to the previous instructions.®®Note: If you are a brave person and do not care about your current Control Table settings or Macros, a very fast way to set the Initial Setup mode is to reset all settings to the FACTORY DEFAULT. The accomplish this:®®1. Turn the printer on while pressing the FUNCTION switch to enter the Initial Setup mode. The ON LINE indicator light should be blinking.®®2. Press the FF switch®®3. Press the SET switch®®4. Press the FUNCTION switch to release the Initial Setup mode.®®The printer is now set correctly to work with PowerPrint.®®If you are not that brave (we don’t blame you) follow these instructions step by step to set the Initial Setup mode:®®1. Turn the printer on while pressing the FUNCTION switch to enter the Initial Setup mode. The ON LINE indicator light should be blinking.®®2. Press the ROW switch once and ensure the indicator light on C1 is lit. If the indicator light is not lit press the COLUMN switch to change this setting. Once C1 is lit, press the SET switch to save this setting.®®Note: In the ROW indicator condition: ON=light is lit, BLK=light is blinking, OFF=light is out.®®Note: When changing a column setting (using the column switch to change a setting) the Initial Setup mode, a lit indicator light means setting is ON, while a blinking indicator light is OFF. See page 3-14, number 2 in the printer manual.®®3. Press the ROW switch six (6) times and ensure the lights are OFF for C1, OFF for C2, OFF for C5 and OFF for C6. C3 and C4 do not matter. If the KX-P38 cut sheet feeder is installed, the indicator light should be ON for C2. If the indicator lights are not set correctly use the COLUMN switch to change these settings. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®4. Press the ROW switch once and ensure the lights are OFF for C1, ON for C2, OFF for C3, OFF for C4, and OFF for C5. C6 doesn’t matter. If you have to change any of the settings, use the COLUMN switch to do so. We recommend you make all the necessary changes then press the SET button before moving to the next step. This will save the settings you have just made.®®5. Press the FUNCTION button and the printer will go back on line.®®The printer is now set correctly to work with PowerPrint.
Roland PR-9101 True True DM P, S opt FX False True D U108185160,00000000
Roland PR-9104 True True DM P, S opt FX False True D U108185160,00000000
Roland PR-9606 True True DM P, S opt FX False True R Roland@PR-2465
Rosetta Technologies RT3105 True False L S, P LJ False False
Rosetta Technologies RT3216 Continuous Laser True True L P, S LJ II False False
Rosetta Technologies RT3316M Contin. MICR Laser True True L P, S LJ II False False
Rosetta Technologies RT4115 True True L S, P LJ II False False
Rosetta Technologies RT4224 True True L S, P LJ II False False
Rosetta Technologies RT4224M MICR True True L S, P LJ III False False
Rosetta Technologies RT4230 True True L S, P LJ III False False
Rosetta Technologies RT4324 Duplex True True L S, P LJ II False False
Rosetta Technologies RT4330 Duplex True True L S, P LJ III False False
Rosetta Technologies RT4430 True True L S, P LJ III False False
Rosetta Technologies RT4530 Duplex True True L S, P LJ III False False
Royal CJP 450 True False IJ P DJ False False
Samsung Finalé 8000 True True L S, P LJ III False False
Samsung SP-0912 True True DM P, S opt FX False False
Samsung SP-0930N True True DM P, S opt FX False False
Samsung SP-2412 True True DM P, S opt FX False False
